Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Starting with the channel fader (e.g.) When the fader operation switch on the DJ mixer is set to NORMAL 1. On the DJ Mixer, change the C.FADER ASSIGN A switch to other than 1 and change the C.FADER ASSIGN B switch to other than 4 2. Push the CH1, CH4 channel fader all the way to the bottom 3. During play or while paused on unit 1 or 2, press [CUE STOP] (Back cue) •Returns to the set point and pauses. 4. When you want to start play, push the CH1 or CH4 channel fader up •At the same time, play begins from the set point on unit 1 or 2. •After you return the channel fader to its original position, unit back cues, and pauses after returning to the set point. Starting with the cross fader (e.g.) When the cross fader operation switch on the DJ mixer is set to NORMAL and to start play on CH1 1. On the DJ Mixer, change the C.FADER ASSIGN A switch to 1 and change the C.FADER ASSIGN B switch to 4 2. Push the cross fader all the way toward CH4 ( ) 3. During play or while paused on unit 1, press [CUE STOP] (Back cue) 4. When you want to start play, push the cross fader in the opposite direction indicated in step 2, towards CH1 ( ) •At the same time, play begins from the set point on unit 1. You can relay play by connecting the control terminals of the two units. ( page 9) Before use: •Turn Auto Cue on for both units, set the auto cue point for the track to be played and back cue. Using two units for relay play Press [PLAY/PAUSE] on the unit to be played first •Once track play finishes on the unit being played, play automatically begins from the unit on standby. •The unit that was played first pauses and cues at the next track’s auto cue point. •You can automatically alternate play between both units by repeating this method. •You can listen to many different tracks by changing the media and selecting the track of the unit in the standby position. •Set the cue point, select the cue bank and back cue on the standby unit to begin relay play from the desired point of the desired track. Note •During play, if power on one of the units is cut or turned off, play may begin on the other standby unit. •You cannot use fader start and relay play at the same time. Using the amplifier and other equipment Connect with the matching input terminals on the equipment (not included). ( page 9) •When using this unit’s DIGITAL OUT terminal, SD Audio is not output. 1 Put the equipment on standby 2 Press [PLAY/PAUSE] to play •Audio played from the connected equipment is output. •You can alternate play by back cueing unit 2 connected to CH4. Push the cross fader all the way toward CH4 Play CH4 CH1 Back cue Push the cross fader all the way toward CH1 Play CH1 CH4 Back cue RQT7114 24 Other functions Before use •Switch [PLAY SELECT] to select the media to be used •Turn [MODE] on the rear panel to TURNTABLE •Insert the SD Memory Card or CD to be used Linking different tracks (e.g.) Using the DJ Mixer, link track A that is currently being played with track B that will be played next. Before use: •Connect main unit 1 (track A) with DJ mixer CH1 and main unit 2 (track B) with CH4. ( page 8) •Adjust buttons and control knobs of CH1 and CH4 on the DJ mixer so mixed sound is output from the master output. (Refer to the DJ mixer’s operating instructions.) •Push the cross fader to the CH1 side to play track A. (Only track A audio is output from the master output (speaker).) 1 Cue track B using the DJ mixer monitor (headphone) (Refer to the DJ mixer’s operating instructions.) •Search for the track’s cue point (first beat) and set the cue point. 2 Match with track A being played on the speaker, on unit 2 (track B) Press [PLAY/PAUSE] to play track B •Track A is only output on the speaker, track B is output from the monitor headphones. 3 Adjust [TEMPO] on unit 2 (track B) and match the BPM (beats per minute) on track A and track B by listening •Use [TEMPO] on unit 2 (track B) to adjust track B’s BPM value to approximately match the BPM value of track A indicated in the display. 4 On unit 2 (track B), Stop the platter slip surface and press [CUE STOP] to return to the cue point 5 Match with track A again, on unit 2 (track B) Press [PLAY/PAUSE] and play track B 6 Checking the audio through the monitor (headphones), gradually slide the mixer’s cross fader towards the CH4 side •Track B audio is mixed with track A audio from the speaker and output. •When the cross fader has been completely moved to the CH4 side, the transition from track A to track B is complete. BPM Using with other equipment Initializing this unit’s memory Unit’s initialize memory function You can re-initialize all memory content on this unit, restoring it to factory settings. Re-initializing will erase the following memory. •Cue bank, cue pad, loop play •Vinyl simulator, dynamic effect settings •Auto Cue on, off settings and auto cue level settings •Instant change settings 50 CDs or SD Memory Cards worth of data items of the above indicated media data. •Display angle, display contrast settings W...