Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
At the same time, the battery capacity monitor will display the fully charged condition (see fig. 2 (A)). The battery capacity monitor will turn off in about 10 minutes after the charging has been completed (see fig. 2 (B)). You can fully charge the shaver in 1 hour if the battery capacity monitor flashes down to the 20% level. A full charge will supply enough power for about 14 shaves (3 min 7 utes per shave for a normal beard). You can always store your shaver in the charging adaptor battery capacity. This shaver cannot be overcharged. Before traveling, charge it fully for 1 hour if you will not be taking the charging adaptor with you. In case your shaver is without charge, you may quick charge it for 1 shave in about 5 minutes. Using your shaver Push the On/Off switch to turn the shaver on. If you push and hold the On/Off switch for more than 2 seconds, it will activate the turbo mode for “ sonic” vibration cleaning. (see “ Cleaning your shaver” ) Caution: Shaving with “ sonic” vibration may damage your skin. Please turn it off and on again to deactivate the turbo mode. Hold the shaver at a right angle (90° ) to your skin (see fig. 3). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. Pivot action selector (see fig. 4) Use the pivot action selector to choose the shaving mode. soft, • , lock based on shaving preference. The pivot action can be matter whether the is turned on or off. For wet shaving Put a thin layer of shaving foam on your face which works as a lubricator. Shaving foam is the most suitable among many other shaving aids (gel, soap, cream, etc). Do not put a thick layer of shaving foam as it may affect shaver’s performance. If the shaving head is clogged with foam, simply rinse it under running water. System outer foil (see fig. 5) System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face. The slit blade catches and cuts longer and lying hairs easily. Using the trimmer (see fig. 6) Slide the trimmer handle up until it clicks in. Place the trimmer at a right angle to your skin and move it downward to trim sideburns. Cleaning your shaver (see fig. 7) For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while preventing odors or bacteria from developing, and maintain the cutting per 8 formance. With the system in place, apply some hand foil. Push the On/Off more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning. At the same time, the lamps of the Battery capacity monitor/Charge status lamp will flash around randomly. Pour some water over the outer foil. After about 20 seconds, it will be automatically turned off, or you can turn it off by pushing the On/Off switch. Remove the system outer foil and clean it with running water. Wipe off any moisture from the shaver with a dry cloth and remove the protective cap to allow the system outer foil to dry completely. Replacing shaving head components It is recommended that you replace the system outer foil at least every year and the inner blade at least every 2 years to maintain your shaver’s cutting performance. Replacing the system outer foil (see fig. 8) Squeeze the system outer foil release buttons and lift the system outer foil upward to remove it. To insert the new system outer foil, press it down until it snaps into place. Replacing (see fig. 9) Squeeze the system outer release buttons and lift the outer foil upward to remove it. Remove the inner blade one at a time by grasping it firmly at both ends and pulling straight away from the shaver. Do not touch the metal parts of inner blades. To insert the new inner blade, hold the blade one at a time at both ends and press downward until it snaps into the shaver. ATTENTION: A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. How to remove the built-in rechargeable batteries before disposal of the shaver (see fig. 10) The batteries in this shaver are not intended to be replaced by consumers. However, the batteries may be replaced at an authorized service center. The procedure described below is intended only for removal of the rechargeable batteries for the purpose of proper disposal. 1. Slide the trimmer handle up until it clicks in. 9 2. Remove the screw (a) and panel cover (b). 3. Remove the two screw covers (c) (using something a toothpick), and 6 screws (d). 4. Remove the back panel (e). 5. Lift the battery block (f) and remove it from the battery terminal sealing (g). 6. Remove the batteries from the battery bloc...