Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Continue rotation until the desired volume level is obtained. © TONE CONTROL Rotate this knob either to the left or right to adjust the desired tone reproduction. Rotating the knob clockwise will increase treble response and counter-clockwise will increase bass response © LEFT/RIGHT BALANCE CONTROL(PULL) Pull this knob outward until it locks into outer position. Rotate it to the left or right to obtain the desired balance between left and right speakers. Push knob back in to return to volume control position. © FRONT/REAR FADER CONTROL Rotate this knob to the left or right to obtain the desired balance between front and rear speakers in 4 speaker installations. When used in conjunction with the Left/Right Balance Control®, you have full 4-way stereo balance capability. (D FM/AM BAND SELECTOR Each time this button is pressed, the radio band is changed.The indications "AM1"or"AM2", "FM1" or "FM2"or"FM3" will appear in the display panel according to you selection. @ &© MANUAL UP/DOWN TUNING To manually select a radio station press the Up Tuning(UP) button© to advance the unit one digit higher or Down Tuning (DIM) button 6) to tune downward. Pressing either button for longerthan 0.5 second will cause the radio to tune rapidly in the selected direction. ® AUTO-STORE TUNING(AS) PRE-SET SCAN TUNING (PS) During radio operation, press this button momentarily to scan the twelve stations pre-set into the memories of the AM bands or the eighteen pre-set memories of the Flvl bands, The unitwill stop at each pre-set station for 5 seconds before continuing to the next pre-set station(the channel indicator number on the display will flash). Press the button again momentarily to stop the Pre-set Scan operation and remain on the selected frequency. Pressing the button for longer than 1 second will activate the Auto-Store Tuning .which will automatically scan the band and enter the six strongest stations into the six pre-set memory positions for each band. If you have already set the pre-set memories to your favorite stations, activating the Auto-Store feature will erase those stations and enter the new strong stations. This feature is most useful when travelling in a new area where you are not familiar with the local stations. (9) STATION PRE-SET MEMORIES To set any of the 6 pre-set memories, use the following procedure: 1. Turn the unit on and select the AM1 band. 2. Select the first station to be pre-set using the Manual Tuning © &© . 3. Press the pre-set button to be set and continue to hold the button in. The volume will be muted for approximately 2 seconds and then return. The station is now set into that pre-set button. To recall that station, press the button momentarily. 4. Repeat the above procedure for the remaining 5 pre-sets on the band. 5. Select the AM2 band and enter 6 FM memories using the same procedure as above. In similar fashion, enter 6 pre-set memories on the FM1 ,FM2,FM3 Band. @ LIQUID CRYSTAL DISPLAY PANEL The Liquid Crystal Display(LCD) panel displays the frequency, time and activated functions. Note: It is a characteristic of LCD panels that if subjected to cold temperatures for an extended period of time, they will take longer to illuminate than under normal conditions, In addition, the visibility of the numbers on the LCD may sightly decrease, The LCD read-out will return to normal when the temperature increases to a normal range. @ CASSETTE DOOR Hold the cassette with the exposed tape edge to the right and insert into the cassette door. Depress fully until the cassette is engaged and begins playing. Note: Observe cassette operation Cautions in Care and Maintenance section of this manual. 0 FAST-FORWARD/EJECT BUTTON This button performs two functions. To eject a cassette, simply press the button fully in and release. The cassette will eject and radio operation will resume. To fast-forward the tape, depress the button half-way in to the locked position. To stop fast-forward and resume normal tape playback, depress the button slightly and release. Do not press fully In or the cassette will be ejected. © TIME/FREQUENCY SELECTOR (CLK) During radio operation, push this button to call the time display on the incorporated quartz clock. Pressing the button again will return to frequency display, or it will automatically return after approximately 5 seconds. SETTING CLOCK 1. Switch vehicle ignition "on" and radio "off’ (time display will show on LCD Panel) 2. Press and hold the Time /Frequency Selector(CLK). at the same time, Press the Down Tuning button © to adjust the hours , then the Up Tuning button © to adjust the minutes. 3. After setting the correct time , release the Time/Frequency Selector. WIRING DI AGRAM SPECIFICATIONS Size: 7"(W) x 2" (H) x 6 1/8"(D) 178mm x 50mm x 156mm Operating Voltage: 12VDC, Negative Ground Output Power: 50 Watts Max. Stereo Power Output Wiring: Floating Ground type designed for 4 speaker use May also be used with 2 speaker. Output...