Оценок - 3, средний балл: 3.3 ( )

Производитель: American Panel Размер: 2.17 mb Название файла: Язык инструкции:

Choose electric defrost only if your unit is equipped with electric heaters. Otherwise choose “Air Flow” defrost. If the defrost cycle type is set to electric, the controller will display: Use and buttons to increase or decrease the evaporator temperature at which the controller will finish the defrost cycle. Press when done. If the defrost cycle type is set to “Air Flow” the controller will display: Use and buttons to increase or decrease the length of the defrost cycle. D.5.4. Parameter Programming For UV Cycle The controller will ask the operator to choose an operating cycle. Press to set the parameters for the UV cycle. Use and buttons to increase or decrease the amount of time in which the Germicidal Lamp will be on. Press when done. Note: The UV cycle is an optional feature. Program the UV cycle only if the unit is equipped with a Germicidal Lamp. D.5.5. Parameter Programming For Print Cycle The controller will ask the operator to choose an operating cycle. Press to set the parameters for the print cycle. Use and buttons to set the printer ON or OFF. Press when done. Note: If the print mode is ON, the printer will print events at preset time intervals. If the print mode is set , the events will be saved in the controller’s memory. Use and buttons to increase or decrease the time interval at which the controller will save the events (status of the unit, time, air temperature, and food temperature) Press when done. Press to exit programming mode. Note: The controller is able to save 250 operating events, approximately 72 hours of normal operation. To store the new information the operator will have to clear the events memory. (See chapter E.7) Note: The Printer is an optional feature. Program the Print cycle only if the unit is equipped with a Printer. D.6. Programming The Alarms The unit’s control panel is equipped with two types of alarm systems: Food Probe Alarm – it will sound when the food has reached the desired temperature, or when the food temperature is too high. The Food Probe Alarm is informative only and it will not stop the unit. Air Probe Alarm – it will stop the unit in case the air temperature inside the cabinet goes out of the preset temperature range. The Air Probe Alarm is a protective system. In case it does go off, the unit should be inspected and, when safe, restarted. D.6.1. Setting The Food Probe Alarms Make sure the control panel is in OFF mode. Press and hold and , at the same time, for five seconds. The display will show: Use and buttons to increase or decrease the desired end temperature of the food. The red food probe alarm will go off if the food temperature goes below this point. Press when done. Use and buttons to increase or decrease the high temperature point. If the food temperature is grater than this point, the red food probe alarm will go off. Press when done. If your unit is equipped with additional food probes, repeat the previous procedure for the rest of the food probes: Yellow, Blue, and Green. D.6.2. Setting The Air Probe Alarm Note: The Air Probe Alarm temperature set points are critical for the good functioning of the refrigeration system. Therefore, these limits should be set only by a qualified factory technician. Make sure the control panel is in OFF mode. Press and hold and , at the same time, for five seconds. The display will show: Use and buttons to increase or decrease the low limit temperature point at which the controller will shut off the unit. Press when done. Use and buttons to increase or decrease the high limit temperature point at which the controller will shut off the unit. Press when done. The Parameter Programming is now complete. IT IS NOW SAFE TO OPERATE THE UNIT. D.7. Recipe Names Note: The controller can store up to 150 recipe names. A recipe name must not be longer than 12 characters. Make sure the control panel is in OFF mode. Press and hold for five seconds. The display will show: Use and buttons to scroll to the desired recipe number. To edit the recipe name, press . Use and buttons to scroll thru the characters. Press to move to the next character or to add characters. Press to save the change and to move to the next recipe number. To exit recipe name programming mode, press . Note: Do not press before pressing. The changes for that particular recipe number will not be saved. To delete a character press . E. Printer (Optional) NOTE: The printer is delivered fully installed E.1. Loading A Roll Of Paper 1. Remove the printer cover by pressing on the groove patterns to pop the front edge up. Lift off the cover. 2. Press the rocker switch to the left. The light will go off. 3. Unroll several inches of paper. 4. Cut a straight edge on the paper roll if it is jagged. This will facilitate the entry of the paper into the printer. 5. Slide the paper through the slot connecting the paper compartment and the printer compartment. It can be slid in about .” before it stops. 6. While holding the paper in place, press the rocker switch to the Pa...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: