Оценок - 2, средний балл: 5 ( )

Производитель: Samsung Размер: 4.6 mb Название файла: Язык инструкции:

К этому устройству также есть другие инструкции:

Мониторы - NC241-T (4.64 mb)

Figure 2-2: OSD Options Menu 2.4.4 Configuration Window The Configuration option on the Administrative Web Interface and OSD lets you configure various settings for the device. The tabs in the Configuration window are: Network IPv6 Label Discovery Session Language OSD Display Reset Each tab has the following buttons: OK, Cancel, and Apply. These buttons allow the administrator to accept or cancel the changes made. 362 Using "PCoIP" 2 2 Using "PCoIP" The OSD configuration options are a subset of the options available in the Administrative Web Interface. To make changes to the configuration settings, you will need an administrator password. You do not need a password to view the Diagnostic and Information menus. Applicable only when the Password item is available. Network Tab You can configure the host and client network settings from the Initial Setup page or Network page. After you update the parameters on this page, click Apply to save your changes. The Network parameters can also be configured using the Administrative Web Interface. Figure 2-3: Network Configuration • Enable DHCP When Enable DHCP is enabled, the device will contact a DHCP server to be assigned an IP address, subnet mask, gateway IP address and DNS servers. When disabled, the device requires these parameters to be set manually. • IP Address The IP address of the device. If DHCP is disabled, you must set this field to a valid IP address. If DHCP is enabled, you cannot edit this field. • Subnet Mask The subnet mask of the device. If DHCP is disabled, you must set this field to a valid subnet mask. If DHCP is enabled, you cannot edit this field. It is possible to configure an illegal IP address/subnet mask combination (e.g., invalid mask) making the device unreachable. Ensure you set the subnet mask properly. 372 Using "PCoIP" 2 2 Using "PCoIP" • Gateway The gateway IP address of the device. If DHCP is disabled, this field is required. If DHCP is enabled, you cannot edit this field. • Primary DNS Server The primary DNS IP address of the device. This field is optional. If the DNS server IP address is configured using the Connection Manager, the address may be set as an FQDN instead of an IP address. • Secondary DNS Server The secondary DNS IP address of the device. This field is optional. If the DNS server IP address is configured using the Connection Manager, the address may be set as an FQDN instead of an IP address. • Domain Name The domain name used (e.g., 'domain.local'). This field is optional. This field specifies the host or domain of the client. • FQDN The Fully Qualified Domain Name for the host or client. The default value is pcoip-host- or pcoipportal- where is the MAC address of the host or client. The domain name is appended if used (e.g., pcoip-host-.domain.local). This field is read-only on this page. • Ethernet Mode Lets you configure the Ethernet mode of the host or client as: • Auto • 100 Mbps Full-Duplex • 10 Mbps Full-Duplex When you choose 10 Mbps Full-Duplex or 100 Mbps Full-Duplex and then click Apply, a warning message will appear. "Warning: When Auto-Negotiation is disabled on the PCoIP device, it must also be disabled on the switch. Additionally, the PCoIP device and switch must be configured to use the same speed and duplex parameters. Different parameters may result in a loss of network connectivity. Are you sure you want to continue?" Click OK to change the parameter. You should always set the Ethernet Mode to Auto and only use 10 Mbps Full-Duplex or 100 Mbps Full-duplex when the other network equipment (i.e., switch) is also configured to operate at 10 Mbps Full-Duplex or 100 Mbps Full-duplex. An improperly configured Ethernet Mode may result in the network operating at half-duplex which is not supported by the PCoIP protocol. The session will be severely degraded and eventually dropped. IPv6 Tab The IPv6 page lets you enable IPv6 for PCoIP devices connected to your IPv6 network. • IPv6 is not currently supported by VMware View. 382 Using "PCoIP" 2 2 Using "PCoIP" • When you make a change to one of the settings on this page, you must reboot your device for the change to take effect. Figure 2-4: IPv6 Configuration • Enable IPv6 Enable this field to enable IPv6 for your PCoIP devices. • Link Local Address This field is automatically populated. • Gateway Enter the gateway address. • Enable DHCPv6 Enable this field to set up Dynamic Host Configuration Protocol version 6 (DHCPv6) for your device. • Primary DNS The primary DNS IP address of the device. If DHCPv6 is enabled, this field is automatically populated by the DHCPv6 server. • Secondary DNS The secondary DNS IP address of the device. If DHCPv6 is enabled, this field is automatically populated by the DHCPv6 server. • Domain Name The domain name used (e.g., 'domain.local') for the host or client. If DHCPv6 is enabled, this field is automatically populated by the DHCPv6 server. • FQDN The fully qualified domain name for the host or client. If ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: