Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Cancels the selection of a Highlight Zone and reverts to the original screen. Automatic detect Manual detect Exit Program Auto Detect Picture Setting Full Screen Highlight Off Other Features Other Features The Highlight Zone function remembers the variables of the selected areas in Automatic and Manual Detect modes, respectively. 1. If the window selected as a Highlight Zone is moved or its size changed, the Highlight Zone changes accordingly. 2. If an un-selected window overlaps the window selected as a Highlight Zone, the Highlight Zone of the selected window turns off. However, it does not turn off the Zone completely and only makes the window shift to standby mode while the settings are saved. When the window is reactivated, the Highlight Zone turns on again with the settings unchanged. 3. If another un-overlapped window beside one with a Highlight Zone is selected as a Highlight Zone, Highlight Zone function is activated for the two separate windows simultaneously. (Up to two windows can be selected as a Highlight Zone and if another window is selected as a Highlight Zone, the Highlight Zone of the previous windows turns off.) When the Highlight Zone is created using the Drag function, the Zone functions independently of the above since it uses a random portion of the screen instead of a particular window. Note 1 : How to cancel the saved variables of a selected window. 1) When a window selected in Automatic Detect mode is replaced with another window also selected in Automatic Detect mode, only the last selection is saved, and the Highlight Zone function is de-activated for the previous windows. 2) In Manual Detect mode, only the window (or the frame window) created last is saved, and the Highlight Zone function is de-activated for the previous windows. The Highlight Zone is de-selected when the program used to create the selected window is closed. The variables of the Highlight Zone created using the Drag function are not saved. Note 2 : The changes saved under Picture Setting of the Highlight Zone menu remain effective even after the program is closed using Exit Program. (The next time you start the Highlight Zone program, the settings are shown as previously saved.) Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. The image on the screen is shaking. Check List Is the power cord connected properly? Can you see "" on the screen? If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen. Can you see "" on the screen? There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) Are there any Solutions Check the power cord connection and supply. Check the signal cable connection. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer. You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle. Adjust the maximum resolution and frequency that the monitor can handle properly. The monitor is in PowerSaver mode. Press any key on the keyboard to activate the monitor and restore the image on the screen. The signal from the video card exceeds the maximum resolution and frequency of the monitor. Move the monitor away from Don..t know whether the Check the icon on the taskbar. Highlight program is running. ( ) indicates the function is activated and ( )shows it has been deactivated. When a Highlight Zone is on, Monitors with the Highlight Zone feature are equipped with an the rest of the screen dims. Automatic Beam Control function. When activated, this may cause slight dimming of the surrounding screen. However, this does not indicate a malfunction of any kind, and it is safe to continue to use the product. The Highlight Zone appears too Check the Contrast value in Picture Setting and adjust it for your dark. ideal viewing. Want to adjust the position and You can change the position and/or the size of the Highlight Zone size of the Highlight Zone. easily using the Manual Detect function. See (Highlight Zone III functions) Cannot select Picture Setting. The Picture Setting feature can be selected only when the Highlight Zone function is on. Turn the Highlight Zone function on before selecting Picture Setting. Self-Test Feature Check Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self tes...
Эта инструкция также подходит к моделям:Мониторы - 796MBPLUS (2.69 mb)