Оценок - 2, средний балл: 4.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
2 3 4 5 4 Setting up Your LCD Monitor 4 English 6 Figure 3.2 DVI-I Cable Connection (SyncMaster 170T only) 1 Turn off your computer and unplug its power cord. 2 Connect the signal cable to the DVI-I connector (1) on the back of your monitor. Connect the other end of the cable to the video port on the back of your computer. 3 Connect the power cord for your monitor to the power port on the power adapter. 4 Secure the power adapter cord and the signal cable(s) under the metal prong. 5 Insert the tab on each side of the hinge cover (b) then attach the stand of the monitor. 6 Plug the power cords of your computer and your monitor into a nearby outlet. 7 Turn on your computer and monitor. If your monitor displays an image, installation is complete. 8 Perform the auto adjustment procedure as described in “Auto Adjustment” on page 7. (1) (b) (a) Setting up Your LCD Monitor Setting up Your LCD Monitor Getting Help If your monitor does not display an image, check your cable connections and refer to “Troubleshooting” on page 18. If you experience difficulties with the quality of the displayed image, run auto adjustment again and refer to “Adjusting Your LCD Monitor” on page 10 or “Troubleshooting” on page 18. Plug and Play Our adoption of the new VESA® Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification (EDID) data using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the LCD Monitor. Auto Adjustment Even though your computer system can recognize your new LCD Monitor system, the auto adjustment function will optimize the display settings for use with your computer. Auto Adjustment can be accessed through the On Screen Display, see “Image Lock:” on page 14 or use the direct access instructions below: Turn on your computer and monitor. 1 Push the AUTO button to open the Auto Adjustment OSD. 2 The screen will dim and you may notice small changes to the screen image. 3 Installing the Video Driver When prompted by the operating system for the monitor driver, insert the Driver diskette included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. English 7 Setting up Your LCD Monitor Windows® 98 Windows® 98 will auto-detect your new monitor and start the “Add New Hardware 1 Wizard” if the drivers are not already installed. Click the NEXT button to search for drivers. Check the diskette drive box to install the drivers off the diskette provided with your 2 monitor and click NEXT. Confirm that Windows found the driver on the diskette and click NEXT again to install 3 the driver. To manually install or update the driver, follow the directions below: Click on START, SETTINGS, CONTROL PANEL, DISPLAY SETTINGS tab, 1 ADVANCED, MONITOR tab, CHANGE. This will start the “Add New Hardware Wizard”. Follow the same directions as given in the steps in the section above. 2 Windows® 95 To determine the version of Windows® 95 that your computer uses, right click on the My Computer icon on the Windows desktop and select Properties. The version number can be seen on the General section under “System:”. Follow the directions given below according to the version of your Windows® 95 operating system: Version 4.00.950A Click on START, SETTINGS, CONTROL PANEL, DISPLAY SETTINGS tab, 1 CHANGE DISPLAY TYPE, CHANGE, HAVE DISK. Type the diskette drive letter in the box and click OK. 2 Version 4.00.950B Click on START, SETTINGS, CONTROL PANEL, DISPLAY, ADVANCED 1 PROPERTIES, MONITOR tab, HAVE DISK. Type the diskette letter in the box and click OK. 2 English 8 Setting up Your LCD Monitor Self-Test Feature Check (STFC) Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly connected but the monitor screen remains dark and the power indicator is blinking, run the monitor self-test by performing the following steps: 1 Turn off both your computer and the monitor. 2 Unplug the video cable from the back of the computer. 3 Turn on the monitor. If the monitor is functioning properly, you will see a white box with a red border and black text inside as shown in the following illustration: Check Signal Cable No Connection Figure 4. Monitor self test screen The three boxes inside the border are red, green and blue. Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. Turn off your monitor and reconnect the video cable; then turn on both your computer 4 and the monitor. If your monitor scr...