Оценок - 1, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
For specific issues, contact the relevant computer or video card manufacturers. 1) Click Start > Settings > Control Panel > Display > Settings > Advanced > Adapter > Update Driver > Next > Display a list of the known drivers for this device so that I can choose a specific driver > Next > Have Disk (Insert Video Card Driver diskette) > OK > Next > Next > Finish. 2) In case you have Adapter Driver Setup file on your computer: Run Setup.exe or Install.exe, which is found in the Adapter Driver Setup file. 4. Maintenance and Cleaning 1. Maintaining the Monitor Case. Clean with a soft cloth after disconnecting the power cord. • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend a Samsung cleansing agent is used to prevent damage to the screen. 2. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repair of damages caused by him/her. 5. Symptoms and Recommended Actions A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact the service center or your dealer. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if you installed the adapter(video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 56Hz ~75Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. The following table lists possible problems and their solutions. Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Problems related to Installation | Problems related to Screen | Problems related to Audio | Problems related to Remote Control 1. Problems related to Installation Problems related to the monitor installation and their solutions are listed. Problems Solutions PC Mode It appears the PC does not function normally. ..Check if the Display Adapter Driver (VGA Driver) is properly installed. (Refer to Installing Driver) The monitor screen flickers. ..Check if the signal cable between the computer and the monitor is securely connected and tightened. (Refer to Connecting to a Computer) TV Mode TV screen is blurred or shows noise signals. ..Check if the TV antenna connector is securely connected to the external antenna. (Refer to Connecting to TV) TV signal is not received ..Check "Channel system" and make sure you choose the correct channel system. (Refer to the Channel System) ..Select "Auto program" to configure the channel system automatically. (Refer to the Auto Program) 2. Problems related to Screen Problems related to the monitor screen and their solutions are listed. Problems Solutions Screen is blank and power indicator is off ..Ensure that the power cord is firmly connected and the LCD monitor is on. (Refer to the Connecting the monitor) "Check Signal Cable" message ..Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting the monitor) ..Ensure that the PC or video sources are turned on. "Not Optimum Mode" message ..Check the maximum resolution and the frequency of the video adapter. ..Compare these values with the data in the Preset Timing Modes Chart. Picture rolls vertically. ..Check if the signal cable is securely connected. Connect it again securely. (Refer to Connecting to a Computer) Image is not clear. Picture is blurred. ..Run Frequency Coarse and Fine tuning. ..Turn on again after removing all accessories (video extension cable, etc.) ..Set resolution and frequency to the recommended ranges. Picture image is unstable and vibrates. ..Check if the resolution and frequency set for the computer video card falls in the range supported by the monitor. If not, reset them referring to the current Information under the monitor menu and Preset Timing Modes.Ghost images are shown in the picture. The image is too light or too dark ..Adjust the Brightness and Contrast. (Refer to the Brightness, Contrast) Screen color is inconsistent. ..Adjust color using Custom under OSD Picture menu. Color image is distorted withdark shadow...