Оценок - 2, средний балл: 4.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
3. Turn on the monitor and Macintosh. Connecting to other devices This monitor allows the user to connect it to such input devices as a DVD player, a VCR a camcorder, a DTV or a TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. 1-1. Connecting AV Devices The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on. 1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal of the monitor using the S-Video cable. S-Video, RCA cable and EXT(RGB) cable are optional. 2. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R and L audio input terminals using audio cables. 3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. 4. Select AV or S-Video using the SOURCE button on the monitor. 1-2. Connecting EXT(RGB) - It only applies to AV DEVICE that supports SCART. Connect to the DVD Devices input if the device has a DVD connector. You can watch DVD simply by hooking up the DVD with the monitor as long as the power is on. 1. Connect a video cable between the EXT(RGB) jacks on the Monitor and the EXT(RGB) jacks on the DVD Player. 2. Select Ext. by pressing SOURCE button on the monitor. 2. Connecting TV You may view television programs on the monitor if it is connected to an antenna or a CATV cable without installing any separate TV reception hardware or software on your computer. 1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor. You need to use a coaxial antenna cable. When using an interior antenna terminal: Check the antenna terminal on the wall first and connect the antenna cable. When using an outdoor antenna: If you are using an outdoor antenna, use a professional for installation if possible. To connect the RF cable to the antenna input terminal: Keep the copper wire portion of the RF cable straight. 2. Turn on the monitor. 3. Select TV using SOURCE button among the external signal adjustment buttons. 4. Select a desired TV channel. Is weak signal causing poor reception? Purchase and install a signal amplifier for better reception. In areas where Antenna cable is not supported, first, attach connector to TV antenna . 3. Connecting DVD/DTV Set Top Box Connect to the DVD/DTV Set Top Box input if the device has a DVD/DTV connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on. 1. Connect the Audio (R) and Audio (L) outputs on the DVD / DTV set top box to the Audio (R) and Audio (L) inputs on the monitor using audio cables. 2. Connect a video cable between the component( PR, PB,Y) jacks on the Monitor and the PR, PB,Y jacks on the DVD / DTV set top box. 3. Select Component using the SOURCE button on the monitor's front. 4. Connecting Headphone You may connect your Headphone to the monitor. 1. Connect your Headphone to the Headphone connection terminal. 5. Connecting Speakers Make sure to detach the speaker stand before installing the speaker to the monitor. Otherwise damage may be caused to the stand when the monitor is tilted over. 1. Install the speaker. There are two ways as follows A. When installing the speaker into the mains Be sure to hold the LCD set instead of the speakers when moving the LCD set with the speakers attached. (Otherwise may damage the brackets connecting the speakers.) • Detach side covers from both sides of the LCD set. • Fit the side hole of the speaker into the bracket and fix it with screws(Silver 4EA). • Detach side covers from Speakers. Fit the side hole of the speaker into the protruding connector of the bracket. • After both speakers are attached, secure them will the 4 screws (Black: 4EA). B. When separating the speaker from the mains • Secure the Speaker Covers by setting them into the holes located on the front side of the speakers. • Make sure the arrow inside the cover points upward • Secure the Speaker Covers by setting them into the holes located on the front side of the speakers. • Mount assembled speaker on Speaker Stand and then push the speaker to be completely secured. • Be sure that the Speaker Stands are placed correctly referring to following illustration, not to confuse front and back of Speaker Stands. • Place assembled speakers to have adequate distance from the LCD set. 2. Connect the cable in the way the rear terminal of the speaker fits into the rear R-SPEAKER-L terminal of the mains. Using the Stand This monitor supports various types of VESA-standard bases. You need to either fold or remove the base in use in order to install a VESA base. 1. Folding the base The monitor may be reclined from -5 to 15 degrees. 2. Attaching a wall-mount This monitor accepts a 200 mm x 100 mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad 1. Turn off your monitor and unplug its power cord. 2. L...