Оценок - 3, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
The “Delay Touch Setting” properties can be set selectively. The higher the value (unit: millisecond), the longer the touch-delay time; the “Area” value is used to adjust the effective touch area of the touch panel, on which the finger stays. The higher the value (unit: pixel), the wider the effective area. 9. Drag Delay This function allows a drag event to occur only after a certain predefined drag delay time has elapsed. If the object cannot be precisely selected or the cursor jitters, adjust the value of "Drag" to delay dragging. It is displayed in milliseconds. C' I Note According to the hardware statuses and external factors, you can flexibly set related parameters to achieve the best performance. Refer to the attachment later in this manual. Serial port Settings 1. After installing the driver of the serial port is finished, choose “Start”-“All Programs”-“IRTOUCHSYSTEMS”-“Serial Port Settings”. The name of the IR touch device installed and the number of serial ports are shown in the list. Choose [Install] when some serial ports are available or choose [Remove] to uninstall the driver if you don't want to use the touchscreen. Using the Software 2. Click [Change Port] and change the settings of the selected Serial Port. Serial TouchScreen. Manager Instated TouchScreen D»ivet$ For Serial Device ^Serial Pori IRTfll irHSYSTFHWHBi^PB^^H 1 RflMI BH OK Cancel Install Remove Change Port Close Attachment General settings for touchscreen Select "Mouse Emulation" mode to find the available options in Options: "Enable Touch," "Send Right Click" and "Enable Double Click". If you select the "Enable Delay Touch" option, touch sensibility will slow down and dragging after a quick click will be treated as disabled operations. Dragging and fast clicking will be considered disabled operations. Using the Software U3 IRTOUCHSYSTH1S IouchScreen Properties Instructions for the settings: 1. Send Right Click : You can enable the right-click function (default). Click and press on any area on the screen for two seconds. The right-click menu will pop up. Right-click is only available in Mouse Emulation mode. In general, the “Delay” value is set to 1000 (1 second) and the “Area” value is set to 32px, to obtain the best performance regarding the right-click function. 2. Enable Double Click : Same as the mouse's double click function. If you double click an object in accordance with the Speed and Area settings, it will open. The parameter settings for best operation are a “Speed” value between 500 and 550 and an “Area” value of 32px. 3. Drag Delay: This function shows the amount of time (in milliseconds) to wait before “Drag” is executed after being clicked. If the object cannot be precisely selected or the cursor jitters when you attempt to touch, adjust Drag Delay to the correct value by dragging the slide bar. It is displayed in milliseconds. Settings for touchscreen in strong light, rain and snow conditions A snowflake or raindrop can cause an unwanted single touch operation. The "Enable Delay" function will prevent such a false screen touch. Using the Software Specifications 1. Define each value in “Delay Touch Settings” after selecting to activate “Enable Delay Touch”. It is recommended that "Delay" is set between 40 and 50 and "Area" to 2. Note The touch response can be obtained after activating the "False touch rejection" function. MDC (Multiple Display Control) Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MDC installation file. Using the Software \-£.- Note If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MDC executable file on the CD. 3. When the Installation Shield Wizard window appears, click "Next". 4. Select "I agree to the terms of the license agreement" to accept the terms of use. 5. Click "Install". 6. The "Installation Status" window appears. 7. Click "Finish". 8. When the installation is complete, the MDC executable icon appears on your desktop. Double-click the icon to start the program. MDC execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installation Problems The installation of MDC can be affected by such factors as the video card, motherboard and the network environment. Uninstall The MDC program can be removed only by using the "Add or Remove Programs" option of the Windows® Control Panel. Perform the following steps remove MDC. Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select MDC from the list and then click the "Add/Delete" button. 0 Using MDC Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be...
Эта инструкция также подходит к моделям:Мониторы - 700TSN-2 (4.82 mb)