Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
When adding gas to the pressure washer, make sure the unit is sitting on a flat, level surface. If the engine is hot, let the pressure washer cool before adding gas. ALWAYS fill the fuel tank outdoors with the machine turned off. NOTE: Use unleaded gas only. DO NOT mix lubricant with gas. n Before removing the fuel cap, clean the area around it. Remove the fuel cap. n Insert a clean funnel into the fuel tank then slowly pour gasoline into the tank. Fill tank to approximately 1-1/2 in. below the top of the tank neck (this allows for fuel expansion). n Replace fuel cap and tighten until the cap “clicks”. n Clean up any spills before starting the engine. PUMP LUBRICANT The pressure washer pump has been filled with sufficient lubricant at the factory. You do not need to check or add lubricant to the pump. STARTING AND STOPPING THE PRESSURE WASHER See Figures 12 - 14. CAUTION: Do not run the pressure washer pump without water supply connected and turned on, as this may damage the high pressure seals and decrease pump life. Completely unwind the hose from its reel or coil and make sure the hose is not being restricted by tires, rocks, or any other objects that may lessen or prevent water flow to the pressure washer. Before starting the engine: . Connect all hoses. . Check all fluids (lubricant and gas). . Turn on the garden hose then pull the trigger to relieve air pressure; hold the trigger until a steady stream of water appears. To start the engine: n Turn the fuel valve to the ON position. n Move the choke lever to the ON (COLD START) position. NOTE: If the engine is warm, leave the choke lever in the ON (COLD START) position. Allow the engine to run for 5 seconds, and then push the choke to the RUN position. n Put the engine switch in the ON position. n Pull the recoil starter grip until the engine runs (a maximum of 6 times). NOTE: Do not allow the grip to snap back after starting; return it gently to its original place. CAUTION: If the engine does not start after each pull of the starter grip and rope, squeeze the trigger to relieve water pressure before attempting to start the engine again. n Allow the engine to run for 5 seconds, then push the choke lever to the RUN position. To stop the engine: n Put the engine switch in the OFF position. n Pull trigger to release water pressure. USING THE SPRAY WAND TRIGGER See Figure 15. For greater control and safety, keep both hands on the trigger handle at all times. n Pull back and hold the trigger to operate the pressure washer. n Release the trigger to stop the flow of water through the nozzle. To engage the lock out: n Push up on the lock out until it clicks into the slot. To disengage the lock out: n Push the lock out down and into its original position. For the most effective cleaning, the spray nozzle should be between 8 in. and 24 in. from the surface to be cleaned. If the spray is too close it can damage the cleaning surface. SELECTING THE RIGHT NOZZLE FOR THE JOB See Figures 16. Each of the nozzles has a different spray pattern. Before starting any cleaning job, determine the best nozzle for the job. The following chart offers some general guidelines to help you choose the best nozzle for your application. Nozzle Application 0. Red Spot cleaning of high, hard-to-reach areas • Removing caked-on mud from heavy construction, farm, or lawn equipment • Cleaning tar, glue, or stubborn stains from concrete • Cleaning overhead areas • Removing rust from steel and oxidation from aluminum Nozzle Application 25. Green For general purpose or large surfaces • General cleaning of dirt, mud, and grime • Cleaning roofs, gutters, and downspouts • Removing light mildew stains • Removing algae and bacteria build-up from pools • Rinsing surfaces in preparation for painting 40. White For wide-angle rinsing • Light cleaning and washing • Washing and rinsing of painted surfaces and boats • Cleaning roofs, windows, patios, and driveways Soap (Black) For all detergent applications WARNING: NEVER change nozzles without locking the lock out on the trigger handle and NEVER point the wand at your face or at others. The quick-connect feature contains small springs that could eject the nozzle with some force. Failure to heed this may cause personal injury. Using the quick-connect collar, changing nozzles is easy. To connect a nozzle to the trigger handle: n Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure. n Engage the lock out on the trigger handle by pushing up on the lock out until it clicks into the slot. n Pull back the quick-connect collar. n Push the nozzle into place in the spray wand. n Push the collar forward so that the nozzle is secured properly. Check to see that the nozzle is secure. To disconnect a nozzle from the trigger handle once the cleaning job is complete: n Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure. n Engage the lock out on the trigger handle by pushing up on...
Эта инструкция также подходит к моделям:Моечное оборудование - UT80546 (7.69 mb)