Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Check the air filter monthly. For best performance, replace the air filter at least once a year. n Unscrew air filter knob, then remove the air filter cover. n Lift the edge of the air filter carefully and pull it out. n Wash the air filter with warm, soapy water. n Rinse and squeeze to dry. n Reinstall the air filter. NOTE: Make sure the filter is seated properly inside the cover. Installing the filter incorrectly will allow dirt to enter the engine, causing rapid engine wear. n Reinstall the air filter cover. CHECKING SPARK PLUG See Figure 23. n Clean the area around the base of the spark plug before removing to keep dirt and debris out of the engine. Remove spark plug. n Clean off carbon deposits on the spark plug electrode using a plug cleaner or wire brush. Replace the plug if worn. (Recommended spark plug: BPR6HS (NGK) or equivalent.) n Check electrode gap. The gap should be .03 in. (0.7- 0.8 mm). Adjust the gap, if necessary, by carefully bending the ground electrode. n Reinstall spark plug. Tighten securely. CHANGING ENGINE LUBRICANT See Figure 24. n Shut off the engine. n Clean the area around the lubricant fill cap/dipstick, then remove the lubricant fill cap/dipstick. n Tilt the pressure washer on its side as shown. Drain lubricant into approved container. NOTE: Drain the lubricant while the engine is still warm but not hot. Warm lubricant will drain quickly and more completely. n After the crankcase is completely drained, return the pressure washer to an upright position. n Fill with lubricant following the instructions in Adding Lubricant To The Engine earlier in this manual. NOTE: Consult hazardous waste management guidelines in your area for the proper way to dispose of used lubricant. PUMP LUBRICATION The pump on this product was lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. STORING THE PRESSURE WASHER See Figure 25. Store the pressure washer with the gas tank empty by either draining the tank or running the pressure washer until the gas runs out. Allow 30 minutes of “cool down” time before storing the machine. Never place the unit in any position other than upright on its wheels. Store in a dry, covered area where the weather can’t damage it. It is important to store this product in a frost-free area. Always empty water from all hoses, the pump, and the detergent bucket before storing. NOTE: Use of a fuel stabilizer and pump saver will give you better performance and increase the life of the machine. Discharge Fuel: Drain the fuel tank completely. Stored gas can go stale in 30 days. MAINTENANCE Engine Lubricant: Drain the lubricant and replace with fresh, clean lubricant. Spark Plug: n Disconnect spark plug wire and remove the spark plug. Pour about a teaspoon of clean, air-cooled, four-cycle lubricant through the spark plug hole into the combustion chamber. n Leaving the spark plug out, pull the starter cord two or three times to coat the inside of the cylinder wall. n Inspect the spark plug and clean or replace, as necessary. n Reinstall the spark plug, but leave the spark plug wire disconnected. Air Filter: n Clean the air filter. Hoses and Pump: Flush the injection hose with clean water for 1-2 minutes. Remove all hoses. Empty the pump by pulling on the recoil starter about 6 times. This should remove most of the liquid from the pump. Handle: n Pull the handle release knob out and lower the handle to the down position. PREPARING FOR USE AFTER STORAGE n Pull the starter grip with rope three or four times to clean lubricant from the combustion chamber. n Remove spark plug from the cylinder. Wipe lubricant from the spark plug and return it to the cylinder. n Reconnect the spark plug wire. n Refuel the machine as described earlier in the operator’s manual. PERIODIC MAINTENANCE SCHEDULE Maintenance Items Each Use 20 hours 50 hours Check for leakage and loose parts • Check and refill engine lubricant • Change engine lubricant * • Clean spark plug • Clean air cleaner • Replace air cleaner element • Clean fuel cap • Clean and adjust spark plug and electrodes • Replace spark plug • Remove carbon from cylinder head ** • Check and adjust valve clearance ** • Clean and adjust carburetor ** • Check fuel lines • *Initial lubricant change should be performed after first twenty hours of operation. Thereafter change lubricant every fifty hours. Dispose of waste lubricant safely and responsibly. Do not pour into sewage drains, onto garden soil or into open streams. Your local zoning or environmental regulations will give you more detailed instructions on proper disposal. **As to the procedures for these items, consult your nearest Subaru service dealer. TROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine fails to start No fuel in tank Fill tank Spark plug shorted or fouled Replace spark plug Spark plug is broken (cracked porcelain or electrodes broken) Ignition lead wire shorted, broken, or ...
Эта инструкция также подходит к моделям:Моечное оборудование - UT80709 (12.32 mb)