Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Keep in mind that the washer’s detergent system further dilutes the detergent with water, and that some detergents may not be concentrated enough to properly work with the system. Some detergents may not give premix instructions and may require experimenting to determine proper dilution for your application. If you are not familiar with the detergent, always test a small area of the surface to be cleaned for adverse reaction. Do this a day in advance. Thoroughly rinse area with water. Operating the Washer Cleaning WiTh deTergenTs CauTiOn: Wear goggles, respirator, and protective clothing to help prevent injury from detergents and spray. iMPOrTanT: dO nOT direct pressure washer spray at the washer. . Mix detergent as instructed by the manufacturer. . Be sure that water supply is adequate and turned on fully. . Insert detergent strainer into solution (A). Be sure that hose is clear and fully submerged in solution. iMPOrTanT: The detergent system will work only if the detergent nozzle is installed. 4. Install detergent nozzle (B). (Black nozzle with brass body.) 5. Start washer and squeeze gun trigger. If detergent does not spray within one minute, check to make sure the detergent hose is in the solution and is not plugged. 6. To help avoid streaking, apply detergent to the lowest surface first, and move up, using long overlapping strokes. Allow solution to soak for several minutes. iMPOrTanT: remember that high pressure spray can gouge soft woods, damage other materials and loosen grout. 7. Install a pressure nozzle. With the nozzle approximately 6 to 0 inches ( 5 to 5 cm) and at an angle to the surface, power rinse the area from the top down. 8. If surface is not clean, repeat the above procedures. iMPOrTanT: To avoid damage and contamination with other detergents, siphon a gallon (3.78 L) of clear water through the system after each use. PIC89- 0 99R0 b a P -0 07 shuTdOWn iMPOrTanT: shutdown procedures should be followed at the end of each cleaning operation. . If a detergent was used, place detergent inlet strainer in CLEAN water and operate trigger to spray water for a period of three minutes. This will flush the system of detergents and help prevent the detergent valve from sticking or corrosion. . Run engine at idle for - minutes. . Turn engine off by moving throttle lever (A) down to “STOP”. PIC 58• 099R0 a AC-Series Operator’s Manual-E/F Troubleshooting symptom Problem solution no discharge at nozzle when Low pressure or no water supply. Ensure hose is 5/8 in. inside diameter trigger mechanism is squeezed. and incoming water supply is turned on. Obstruction in nozzle. Clean or replace nozzle. Low or fluctuating discharge Inadequate water supply. Use larger I.D. size of hose and pressure. provide specified inlet water pressure and volume. Kink in water inlet hose or in high Remove kink. pressure discharge hose. Water inlet screen obstructed. Remove screen, clean or replace. Pump sucking air. (Pump prime lost.) Tighten all water intake connections. Eliminate leaks in intake line. Not in high pressure mode. Install high pressure nozzle. Obstructed or worn spray nozzle. Remove and clean or replace. Bypass valve not operating correctly. See your John Deere dealer. Water flows from nozzle when Gun malfunction. DO NOT USE!! See your John Deere trigger is released. dealer. Pump oil is white or milky color. Water in oil. Change oil. Avoid directing water spray at pump. detergent will not siphon into Strainer not completely submerged Check, submerge if necessary. Low Pressure Detergent mode. in solution. Strainer obstructed. Inspect, clean or replace. Siphon hose cut, obstructed or Inspect, clean or replace. kinked. Not in Low Pressure mode. Install detergent nozzle. Too many high pressure hose Use only one extension hose extensions attached to outlet. maximum. Detergent valve stuck closed. See your John Deere dealer. Water flows back into detergent Detergent valve jammed, missing See your John Deere dealer. container. or corroded. Oil leaking from pump. Pump failed. DO NOT USE!! See your John Deere dealer. Water leaks from brass valve Thermal Relief Valve opening to Do not run washer with gun trigger on pump. protect pump. closed for more than minutes. Trigger gun to close valve. AC-Series Operator’s Manual-E/F Troubleshooting symptom Problem solution Engine does not start. Fuel tank empty. Fill fuel tank. Throttle lever not in run position. Move throttle lever up to run position. Improper fuel. Drain and Replace. Use correct fuel. Old fuel. Drain and Replace. Use fresh fuel. Spark plug wire loose or Connect spark plug. disconnected. Spark plug not gapped correctly. Check and set spark plug gap. Spark plug failed. Install new spark plug. Ignition parts failed. See your John Deere dealer. engine starts hard or loses Dirt or water in fuel tank. Drain and clean fuel tank. power. Vent in gas cap plugged. Clean vent or install new gas cap. Air cleaner element dirty. Clean or replace air cleaner element. Spark plug ...
Эта инструкция также подходит к моделям:Моечное оборудование - HR-2500GH (10.14 mb)