Оценок - , средний балл: ( )

Инструкция по эксплуатации Campbell Hausfeld, модель PW4035

Производитель: Campbell Hausfeld
Размер: 3.36 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

examine hoses regularly and replace if damaged. do not attempt to mend a damaged hose. uNPACKING Remove the equipment and all parts from the carton The carton should contain the following: • One pressure washer (pump, engine, cart base) • One cart handle assembly • One spray gun and quick connect lance • Five spray tips • One high pressure hose • One pack of nuts, bolts, and manuals If any parts are missing, DO NOt returN the uNIt tO the retAIler. Know the unit’s model number (located on the serial number tag on the pressure washer frame) and call 1-800-330-0712 for replacement parts After unpacking the product, inspect it carefully for any damage that may have occurred during transit Make sure to tighten fittings and bolts before using the pressure washer do not operate the unit if it’s damaged during shipping, handling, or use. damage could result in bursting and cause injury or property damage. ASSeMblY 1 Slide the handle assembly over the lower legs of the cart base. Use the star knob and bolt to secure the legs See Figure 1 Star Knob Figure 1 – Assemble handle 2 . Slide clear plastic detergent hose onto brass hose barb (See Figure 2) Figure 2 – Attach suction tube to barb fitting 3 Insert quick connect spray tips into rubber holders on front of the placard (See Figure 3) 5 Connect the high pressure hose to the pump outlet (See Figures 4 and 5) Figure 5 – Connect high pressure hose to pump 6 Attach the lance with nozzle to the gun (see Figure 6) Figure 3 - Insert spray tips into the holder Figure 6 – Attach lance to gun 4 . Secure garden hose (not included) to the inlet connection on pump (See Figure 4) Garden Hose Pump Inlet Pump Outlet High Pressure Hose Chemical Injector Hose Barb Thermal Relief Figure 4 - Pump hook up 5 Operating Instructions and Parts Manual Pre-Operation (Continued) 7 Install quick connect tip (See Figure 7) Figure 7 - Quick Connect tip trIGGer SAFetY lAtCh In the engaged position, the trigger safety latch prevents the gun from being triggered accidentally Push the latch fully up to engage it (See Figure 8 and 9) Always engage the trigger safety latch when the unit is not in use Figure 8 - trigger locked Figure 9 - trigger unlocked DisengagedEngaged Operation 1. SurFACe PrePArAtION The following cleaning procedure will help you organize your cleaning task and ensures that you will achieve the best results in the shortest amount of time Remember to use the spraying / cleaning techniques mentioned in the following section Before starting a pressure washer cleaning job, prepare the surface you intend to clean Clear furniture from the area and make sure that all windows and doors are closed tightly Also, protect all plants and trees near the cleaning area with a drop cloth A covering ensures that your plants won’t be sprayed by the detergents 2. StArt uP ALWAYS use the following start up procedure to ensure that the unit is started safely and properly If water has frozen in the pressure washer, thaw the pressure washer in a warm room before starting. do noT pour hot water on or into the pump; internal parts will be damaged. 1 . Check engine oil levels Add oil as necessary 2 . Check fuel level Add unleaded gasoline (rated 86 octane or higher) as required do noT refuel a hot engine. refueling a hot engine could cause a fire. use only fresh, clean regular or unleaded gasoline. Close the fuel shutoff valve during refueling. 3 . Attach a garden hose to the inlet side of the pump and connect it to the water supply. Use a hose with an internal diameter (I D ) of 5/8 in (1 58 cm) and a length of 50 ft (15 m) or less some local plumbing codes require backflow prevention when connecting to a fresh water supply. Install a backflow preventer upstream from the pump if necessary. a If inlet water pressure is over 100 psi, install a regulating water valve at the garden hose connection b. Do not exceed 100. F (38. C) inlet water temperature NOte: The inlet water supply must have a minimum flow rate of 5 gpm (19 lpm) 4 Turn the water supply ON never run the unit dry. be sure the water supply is completely turned on before operating the unit. 5 . Trigger the gun until water sprays from the tip indicating that all air is purged from the system Set the trigger safety latch 6 . Open the fuel shutoff valve by turning the lever to the right/“ON” position Close the choke (if the engine is cold) by moving the choke lever fully to the left Move the throttle fully to the left to the “Run” or “Rabbit” position Turn the ON/OFF swirch to the “ON” position Figure 10 - throttle 6 PW4035 Operation (Continued) 7. Start the engine: Unlock the trigger safety latch on the gun Grasp the starter rope and brace one foot on the chassis While squeezing the trigger on the gun, pull the starter rope rapidly and firmly Continue holding the rope as it returns Repeat these steps until the engine starts when pulling the starter rope, make sure to keep your hand and arm clear of the engine and cart co...