Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Barb fitting READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT When using the high pressure setting, DO NOT allow the high pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury can occur. Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! NEVER fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. NEVER fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine. NEVER run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty. NEVER pull water supply hose to move pressure washer. This could damage hose and/or pump inlet. DO NOT use hot water, use cold water only. NEVER turn water supply off while pressure washer engine is running or damage to pump will result. DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged. If you do not understand these precautions, please call 1-866-422-4286 to speak to a service representative for further instructions. D28609 14- ENG STARTING Prior to starting, refer to your engine manual for proper starting procedures for your engine type. 1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners Manual for correct procedure. 2. Check engine oil level. See Engine Owners Manual for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 3. Verify the filter screen is in water inlet of pump. NOTE: Cone side faces out. 4. Connect water source to pump inlet. NOTE: Water source must provide a minimum of 5 gallons per minute at 20 p.s.i. 5. Connect high pressure hose to pump outlet. 6. If applying a chemical or cleaning solution, see How To Apply Chemicals/Cleaning Solvents in Operation section of this manual. Filter Screen 7. To reduce operator fatigue while maintaining a consistent distance from the cleaning surface assemble the 'Water Vroom" cleaning surface guide. See Assembly section for assembly instructions. 8. Turn water source on. NOTE: Failure to do so could cause damage to the pump. 9. Start engine. See Engine Owners Manual for correct procedure. NOTE: If the engine does not start after two pulls, pull the trigger to relieve the pressure. Water Source High Pressure Hose 10. Depress trigger on gun to start water flow. NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick when triggered. NOTE: If using the "Water Vroom" surface cleaning guide, quickly and effortlessly guide it across the flat surface being cleaned. 11. Release trigger to stop water flow. 12. Adjust spray for the task being performed by changing quick connect nozzle. See How To Use Spray Wand instructions in this section. SHUTTING DOWN 1. After each use, if you have applied chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. NOTE: Failure to do so could cause damage to the pump. 2. Turn engine off. See Engine Owner’s Manual. NOTE: NEVER turn the water off with the engine running. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Storage section in this manual for proper storage procedures. 15- ENG D28609 MAINTENANCE When performing maintenance, you may be exposed to hot surfaces, water pressure, or moving parts that can cause serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more frequent maintenance checks will be required. ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for any and all maintenance. PUMP The oil in the high pressure pu...
Эта инструкция также подходит к моделям:Моечное оборудование - D28609 (748.17 kb)