Войти:
Оценок - 3, средний балл: 3.3 ( )

Инструкция по эксплуатации Hobart, модель ML-104651

Производитель: Hobart
Размер: 467.94 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


LEVELING Adjust the feet (or caster legs) so the mixer-grinder is level, both front-to-back and side-to-side. CHECK GEAR CASE LUBRICANT Oil is installed in the gear case at the factory. Make sure oil is at the proper level by checking the oil level sight gauge (Fig. 1). If it is necessary to add oil, unscrew the retaining screws and remove the rear panel (Fig. 1). Remove the oil fill plug (Fig. 1) and add Mobil DTE HM oil until the oil level is brought to the center of the oil level sight gauge. CHECK CHAIN LUBRICANT RESERVOIR Oil is added to the chain reservoir at the factory and sealed at the bottom of the splash shield with a silicone rubber sealant for shipping purposes. With the rear panel removed, remove the sealant from around the chain reservoir (Fig. 1) and inspect the oil level. Replenish as necessary with MPO-30 Multi-Purpose Oil. HOPPER GUARD MIX SWITCH MIX-GRIND SWITCH STOP SWITCH FOOT SWITCH ON-OFF LEVELING FOOT PL-52463 DRAIN PLUG OIL LEVEL SIGHT GAUGE HOPPER GUARD INTERLOCK REAR PANEL SEALANT ON CHAIN RESERVOIR OIL FILL PLUG ELECTRICAL SUPPLY JUNCTION COMPARTMENT Fig. 1 – 3 – ELECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT. When no power cord and plug is provided on the machine, connect the electrical power supply to the leads in the junction compartment (Fig. 1). The compartment is provided with a tapped hole for 1" trade size conduit. Refer to the machine data plate (Fig. 3). Machines ordered with casters are provided with a cord and plug and only require connection to an appropriately sized, grounding-type receptacle. Refer to the machine data plate (Fig. 3) and Electrical Data, below. ELECTRICAL DATA Model Volts / Hertz / Phase Receptacle, Circuit and Plug Size Receptacle and Plug Type Reference 4352 200 / 60 / 3 30 Amps Receptacle Shown G YW Z X NEMA Receptacle: L21-30R Plug: L21-30P 230 / 60 / 3 30 Amps Receptacle Shown G Y Z X NEMA Receptacle: L15-30R Plug: L15-30P 460 / 60 / 3 20 Amps Receptacle Shown G Z Y X NEMA Receptacle: L16-20R Plug: L16-20P Compiled in accordance with the National Electrical Code, ANSI / NFPA 70, 1993 Edition. CHECK MOTOR ROTATION With the grinder attachment in place and the hopper guard closed, check worm rotation before making a permanent electrical connection by first pushing the MIX-GRIND switch and then pushing the STOP switch (Fig. 2). If there is no worm rotation but the mixer arm turns, correct the rotation using the following procedure: DISCONNECT THE ELECTRICAL POWER SUPPLY and interchange any two of the incoming power supply leads. Reconnect the power supply and push the MIX-GRIND switch to verify that both the worm and the mixer arm rotate. CONTROL BOX HEATER The Mixer-Grinder has a heater in the control box to keep the controls dry. It is automatically ON when the machine is el...

Эта инструкция также подходит к моделям:
Миксеры - ML-104650 (467.94 kb)
Миксеры - ML-104654 (467.94 kb)
Миксеры - ML-104655 (467.94 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории