Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Remove all protective materials. Place parts on a non-arasive surface to avoid scratching. If you are missing any parts or are unsure how to proceed with assembly, call our Customer Service Center at 1-800-416-3511 (Mon - Fri 9a-5p EST). Do not attempt assembly if any parts are missing or damaged. Read entire assembly instructions before beginning assembly. STEP 2 WHEEL ASSEMBLY Insert wheel axle (M) through bottom shaft of right side support frame (Q).so that it is centered inside the shaft with equal amount of axle on each side. Snap 12mm end clip (I) on notch in axle closest to the right side support frame (Q). Add the following parts to the axle in this order: 12mm washer (G), wheel cover (O), axle sleeve (P), wheel (N), wheel cover (O), 12mm washer (Q), 12mm end clip (I) as shown in figure 1. Be sure the wheel is inserted over the axle sleeve in a manner that allows it to rotate freely. Secure the wheel assembly on the axle with the 12mm washer clip (I). Repeat procedure for opposite side wheel. STEP 3 LEFT SIDE SUPPORT FRAME ASSEMBLY Screw in the two casters (T) into the bottom of the left side support frame (R) as shown in figure 2. Add the cushion handle grip (S) to the left side support frame (R) as shown in figure 2. Insert two M6 x 50mm bolts (B) through end of cushion grip handle and through the holes in the left side support frame. Add a 6mm washer (E), 6mm nut (D). Tighten with wrench. Do not over tighten. Add M6 PVC cover to the end of each nut. Repeat on opposite side of cushion grip handle. Figure 1 Figure 2 PAGE 1 STEP 4 FRAME ASSEMBLY Connect right side support frame (Q) and left side support frame (R) using the rear support bar (V). Be sure that the hole in the center of the rear support bar is facing up. Add a 10mm washer (F) to a M10 x 55 mm bolt (A) and insert through the left side frame support(r) into the fixed nuts in the rear support bar (V) as shown in figure 3. Repeat for opposite side. (Q). Attach front support bar to middle support frame as shown in figure 3 using a M6 x 16mm bolt. Tighten with wrench. Do not over tighten. With bottom of rear portion of middle support frame resting on the rear support bar, attach front support bar to right side support frame (with wheels) using M6x 16mm bolt (C) as shown in figure 3. Tighten with wrench. Do not over tighten. Attach middle support frame (W) to the rear support bar (V). Align middle support bar with hole in rear support bar as shown in figure 4. Add a 10mm washer (F) to an M10 x 55mm bolt (A). Insert bolt through middle support frame and into the fixed nut inside the rear support bar. STEP 5 COILED SHELF ASSEMBLY Attach coiled shelf (Y) to right side support frame (Q) and middle support frame (W) using M6 x 16 bolts (C) as shown in figure 4. Position coiled shelf between the right side and middle support frames so that coiled portion of the panel is acing towards the bottom. Insert bolts through the holes from behind the coiled shelf and into the fixed nuts inside the right side and middle support frames. Use hex wrench to tighten completely. Do not over tighten. Attach front panel to left side and middle support panels as shown if figure 4 using M6 x 16mm bolts (C). Insert bolts through holes from behind the front panel into the fixed nuts in the front portion of the left side and middle support frames. Tighten using hex wrench. Do not over tighten. Figure 3 Figure 4 STEP 6 SINK ASSEMBLY Install sink drain/stopper assembly (AA) as shown in figure 5. Separate the three pieces and insert the center gasket into the whole in the sink basin. Insert the funnel-shaped portion into the sink drain as shown. From underneath the sink basin, attach the bottom portion of the sink drain/stopper assembly onto the bottom portion of the funnel shaped piece to hold firmly in place. Figure 5 PAGE 2 STEP 6 SINK ASSEMBLY (continued) Position the sink top assembly (Z) over the left side, right side and middle support frames, making sure the holes for the bolts are properly aligned. Once in proper position, use M6 x 16mm bolts (C) to attach sink top/basin assembly to the left support frame. Insert bolts through holes in sink top into the fixed nuts in the left side support frame. Repeat procedure for right side support frame. Insert M6 x 50mm bolts (B) through the holes in the middle portion of the sink top/basin assembly through the holes in the middle support frame. Be sure to insert the bolts in the direction towards the right side support frame as shown in figure 6. Add a 6mm washer (E) and an m6 nut to the end of each bolt. Tighten with wrench. Do not over tighten. STEP 7 FAUCET AND FOLDING COUNTER ASSEMBLY Attach rear faucet panel (CC) to left side support frame and middle support frame using M6 x 16mm bolts (C). Insert bolts outwards through holes from behind the rear faucet panel and into the fixed nuts in the middle support frame. Repeat procedure for opposite side. Tighten bolts using hex wrench. Tighten completely. Do not over tighten. Att...