Оценок - 4, средний балл: 4.3 ( )

Производитель: Echo Размер: 902.37 kb Название файла: Язык инструкции:

6. After engine warm up, gradually depress throttle trigger to increase engine RPM to operating speed. BCOLD START RUN IDLE H L STARTING WARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke. WARNING DANGER The blades should not move at idle. If blades move, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. STOP SWITCH - START/RUN Move stop switch (A) away from the STOP position. 2. START - Pull Rope Lay the hedge clipper on a flat clear area and pull the recoil starter handle (D) until the engine fires. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. 18 18 STOPPING ENGINE 1. RELEASE THROTTLE. Allow engine to idle for a minute. 2. STOP SWITCH - STOP. Move stop switch (A) to STOP position. WARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using hedge clipper again. MAINTENANCE Your ECHO Hedge Clipper is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your Hedge Clipper achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Service Dealer for repairs. SKILL LEVEL Level 1= Easy to do. Most required tools come with unit. Level 2= Moderate difficulty. Some specialized tools may be required. Level 3= Experience required. Specialized tools are required. ECHO recommends the unit be returned to your ECHO dealer for servicing. ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task heading are listed the various part numbers required for that task. See your ECHO dealer for these parts. HEDGE CLIPPER OPERATOR'S MANUAL 19 MAINTENANCE INTERVALS Component/System Maintenance Procedure Before Use Every Refuel Daily or Every 4 Hours 3 Months or 100 Hours 6 Months or 300 Hours Yearly or 600 Hours Air Filter Inspect/Replace I / C I / C R * Fuel Strainer Inspect/Replace I R Fuel Line Inspect/Replace I I * R Carburetor Inspect/Replace C R(1) Choke System Inspect/Replace I Cooling System Inspect/Clean I / C I / C Muffler Spark Arrestor Inspect/Clean/Replace I / C R Gear Housing Grease I (2) Recoil Starter Rope Inspect/Clean I I * Fuel Leaks Inspect/Repair I I I * Spark Plug Clean I / C R * Ignition System Clean/Replace No Maintenance required for coil and flywheel Screws/Nuts/Bolts Inspect/Tighten/Replace I* C = CLEANR = REPLACE,I = INSPECT, IMPORTANT Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. * All recommendations to replace are based on the finding of damage or wear during inspection. (1) Replacement will be required for Commercial use after 600 hours. For Consumer use, cleaning every 6 months is required. (2) Apply 1~2 pumps of ECHO® LUBETM every 10 hours. 20 20 AIR FILTER Level 1. Tools required: 25 or 50 mm (1 or 2 in.) medium bristle paint brush Parts required: 90008 REPOWERTM AIR & FUEL FILTER KIT 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from the air cleaner area. 2. Remove the air cleaner cover. Clean and inspect the element for damage. If element is fuel soaked and very dirty, replace. 3. If element can be cleaned and reused, be certain it: -still fits the cavity in the air cleaner cover. -is installed with the original side out. NOTE Carburetor adjustment may be needed after air filter cleaning/ replacement. FUEL FILTER Level 1. Tools required: 203-254 mm ( 8-10 in.) length of wire with one end bent into a hook. Clean rag, funnel, and an approved fuel container Parts required: 90008 REPOWERTM AIR & FUEL FILTER KIT WARNING DANGER Fuel isVERY flammable. Use extreme care when mixing, storing or handling. 1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. 2. Use the “fuel line hook” to pull the fuel line and filter from the tank. 3. Remove the filter from the line and install the new filter. HEDGE CLIPPER OPERATOR'S MANUAL 21 SPARK PLUG Level 2. Tools required: T-wrench, Feeler gauge, Soft metal brush Parts required: Spark Plug, BPMR-7A 15901010230 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4. Tighten spark plug to 145-155 kg/cm (125-135 in. lb.). COOLING SYSTEM CLEANING Level 2. Tools required: 3 mm Allen wrench, 4 mm Allen wrench, Pointed Wood Stick, Cross head ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: