Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
Allow the engine to cool before storing in any enclosure. 4. To reduce fire hazard, keep the engine free of grass, leaves, or excessive grease. 3 I CONTENTS OF HARDWARE PACK ATTACHING THE LOWER HANDLE AND REAR WHEELS. Shoulder Bolt — Cupped Washer 1/2" I.D. Hex Lock Nut -3/8-16 Thread Axle Bolts' Cupped Washer 3/8" I.D.- Flat Washer 3/8" I.D.-Lock Washers 3/8" I.D.-* Hex Nuts 3/8-16 Thread ATTACHING THE ENGAGEMENT HANDLE AND CLUTCH ROD Cotter. Pins Rod Adjustment Link Hex Bolt 5/16-18 x -1-3/4" Long Compression-Spring Flat Washer 5/16" I.D.— Hex Lock Nut-5/16-18 Thread B ATTACHING THE FRONT WHEELS Push Caps Hairpin Clips Spacer 1/2" I.D. x-1-5/8" Long o ATTACHING THE UPPER HANDLE, THROTTL E CONTROL AND HANDLE PANEL Carriage Bolts -1/4-20 x 1-1/4" Long Lock Washers — 1/4" I.D. — Hex Nuts 1/4-20 Thread Hex Bolts 1/4-20 x 1-1/4" Long -Self-Tapping Screw Hex Lock Nuts-1/4- *0 Thread Hex Bolts 1/4-20 x 1" Long IMPORTANT: NOTE: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, service engine with gasoline and oil as instru ;ted in the separate engine manual packed with your unit. Reference to right or left \ and side of the edger is observed from the operating position. ASSEMEJLY INSTRUCTIONS UNPACKING Tools Required for Assembly ) Adjustable Wrench ) 7/16" Open End or Box Wrench ) 9/16" Open End or Box Wrench ) Pair of Pliers ) Hammer ) Block of Wood 1. Remove the edger from the carton by opening the top flaps and lifting the unit out. Be careful of the staples. Make certain all parts and literature have been removed from the carton before the carton is discarded. 2. Disconnect and ground the spark plug wire against the engine. 3. Stretch out the throttle control cable and place on the floor. Be careful not to bend or kink tb cable at any time during assembly. 4. Separate the contents of the hardware pack according to the illustration above for identification purposes. 4 Hole and Slot in Frame mk Lock Washer FIGURE 1 'Shoulder Bolt Flat Washer Lock 3/8" I.D. Washer Cupped Washer 3/8" I.D. Rear Wheel Cupped Washer Shoulder -j/2" I.D. Bolt FIGURE 2 ATTACHING THE LOWER HANDLE AND REAR WHEELS (Hardware A) 1. Line up holes in lower handle with holes in the frame. Insert axle bolt through left rear wheel (larger), and secure to frame and handle using 3/8" lock washer and hex nut. See figure 1. 2. Assemble the right rear wheel as follows. See figure 2. a. Place 1/2" I.D. cupped washer on shoulder bolt (cupped side of washer goes against the head of the bolt). Insert shoulder bolt through slot in curb height adjuster, frame and lower handle. Secure with hex lock nut. b. Insert axle bolt through rear wheel. Place 3/8" cupped washer on axle bolt (cupped side against the wheel). c. Place 3/8" I.D. flat washer on axle bolt, against cupped washer. Secure to rear hole in curb height adjuster with 3/8" lock washer and hex nut. ATTACHING THE FRONT WHEELS (Hardware B) 1. Using a hammer, tap one push cap onto the end of the front axle which has a hole closer to it. See figure 3. FIGURE 3 5 2. Ill Hub Side of Wheel, Front Axle Hairpin Clips FIGURE 4 -Push Cap Starting on the right side of the edger, place the^ axle through the support arm on the frame. Thei place axle through one wheel so the hub of the wheel is to the outside of the unit. Next place axle through spacer, the other wheel (hub to the outside of the unit) and through second support arm. See figure 4. Secure with push cap by tapping it on with a hammer. See figure 5. It is necessary to hold a block of wood or a second hammer against the push cap on the other side of the axle. 3. Secure the front wheels and axle in position using two hairpin clips. See figure 5. FIGURE 5 ATTACHING THE UPPER HANDLE, THROTTLE CONTROL AND HANDLE PANEL (Hardware C) 1. Slip the three handle grips on the upper handles and the engagement handle. They will slip on more easily if you first soak them in warm, soapy water. 2. Assemble the two upper handles to the lower handle with four carriage bolts, lock washers and hex nuts. Tighten only finger tight at this, time. See figure 6. FIGURE 6 6 A B C] Y y D \ ¥ f\ Screw FIGURE 7 Hex Lock Nut Handle Panel \ Hex Bolt 1" Long Hex Bolt 1-1/4" Long Adjustment Bracket FIGURE 8 3. Assemble the throttle control to the handle panel as follows: A. Hold the throttle control assembly beneath the handle panel. Turn the control sideways and insert the lever up through the wide portion of the slot on the handle panel. See figure 7A. B. After the end of the lever is through the slot, turn and then tip the control forward as shown in figure 7B to slide it through the slot.' NOTE The lever must be all the way to the back of the control housing as shown in figure 7B. C. Push the control back into the slot in the handle panel and press in place. Be certain the control is locked securely into the slot. See figure 7C. D. Secure the throttle control ...
Эта инструкция также подходит к моделям:Машинки для стрижки - 24604-8 (1.42 mb)