Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
If mounted, the comb attachment can be set to 7 cutting length positions. You can slide the control knob when the release button (on top of the knob) is kept pressed-down. When released, the control knob is locked in the selected position. • Clipping with comb attachment - Set the required cutting length (fig. 2). Keeping the control knob pressed-down (1), slide (2) it into one of the 7 positions. Then release the knob. • Clipping without comb attachment - Pull the comb attachment from the appliance (fig. 3). - Insert the appliance plug into the connector (fig. 4). - Insert the mains plug into the wall socket (fig. 5). (Please note: the mains plug and wall socket shown in the illustration are not applicable to the United Kingdom.) - Switch the appliance on (fig. 6). Tips • Ensure that your movements are well-controlled, especially when using without comb attachment. Touch the hair lightly with the hair clipper. • Regularly shake (fig. 7) and/or blow (fig. 8) off the hairs from the top of the clipper. • While clipping with comb attachment: If much hair has accumulated in the comb area, pull off the comb attachment (fig. 9) and remove the hair by shaking (fig. 10) and/or blowing (fig. 11). • If the cutting speed decreases it may be necessary to remove and clean the cutting unit. Please refer to section "Cleaning: after each use". • Always switch off after use. It is advisable to clean the cutting unit directly after use. Cleaning: after each use - Switch off (fig. 12). - Remove the cutting unit (fig. 13). - Clean the cutting unit and the inside of the appliance using the brush (fig. 14); - To reassamble, hook the cutting unit on to the housing as illustrated (fig. 15) and push until you hear a click (fig. 16). Replacement cutting unit Use only an original Philips replacement cutting unit to replace a worn or damaged cutting unit. How to clip General • Ensure that your clipper is clean. • Let the person whose hair you are going to cut sit so that the top of his/her head is on your eye level. Wrap a towel around his/her neck. • Before you start cutting, comb the hair well. Ensure that it is untangled. It is not necessary to wash the hair before cutting. • For good cutting control and a smooth result hold the clipper in a relaxed grip. • The best results will be achieved if the hair clipper is used on dry hair. • When cutting long or semi-long hair it is advisable to cut over a styling comb or to grasp the hair between your fingers as described in section "Cutting over styling comb or fingers". • For short hair, a light trimming at the neck and sides may be all that is needed for a well-groomed haircut. • At regular intervals stop cutting, comb the hair and check the results so far. Hair cutting with comb attachment (4-17 mm remaining hair length) - Begin with the setting for maximum hair length (i.e. position 7). After you have familiarized yourself with the product and have gained some experience, you may select a particular hair length. - You can select seven hair length settings (see fig. 2). Setting Hair length (mm) 7 17 6 15 5 13 4 11 3 9 2 7 1 4 - Before cutting, comb the hair so that it falls naturally. - In general, it is advisable to start from the neck and work towards the top of the head. Next cut the front and the top of the head (fig. 17). Hold the clipper so that the flat side of the comb attachment is directed towards the head. Move it slowly upwards and then away from the head, cutting only a small amount at a time. In the same manner cut the hair at the sides and the back of the head (fig. 18, 19). - If you want the hair cut on the sides or back of the head shorter than on top, change to a lower hair length setting and continue to cut against the direction of the hair growth. Cutting over styling comb or fingers If you want to cut the hair to a length of more than 17 mm, you can use the "over styling comb" method. - Remove the comb attachment (fig. 3). - Lift a small section of hair at a time with a styling comb (fig. 20) or grasp the section of hair between two fingers (fig. 21). Move the comb or fingers through the hair until only the length sticks out which you want to clip off. - Trim the hair protruding from the comb or fingers. Continue this procedure working from the front to the back of the head. As you work to the back, you may gradually cut hair shorter. To check the cutting length, take a cut-off hair section for measuring. - Comb frequently to remove cut hair and to check for uneven areas. Outlining - Comb the hair. - Remove the comb attachment (fig. 3). - For even hair length at the base of the neck cut the hair as shown in fig. 22, holding the clipper in reversed position lightly against the hair. Make overlapping strokes downwards to the neck (fig. 23). - Proceed in the same manner for cutting sideburns (fig. 24). - For cutting the hair close to the ears put one corner of the cutter on the hair. Ensure that the teeth are at a safe distance from the ears (fig. 25). Slowly and care...