DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI ON" LED flashes. "DSI OFF" LED OFF. — 16 — Selectable Illumination Selectable Illumination Selecting the button Display Setting "COL GRN" The illumination color is green. "COL RED" The illumination color is red. Setting the displayed Display Setting "SCL MANU" Doesn't scroll. "SCL AUTO" Scrolls when the display changes. The text scrolled is shown below. • CD text • MD title Local Seek Only stations whose reception is good are searched seek tuning. Display Setting "LO.S OFF" The local seek function is OFF. "LO.S ON" The local seek function is ON. Monaural Reception Noise can be reduced when stereo broadcasts are received as monaural. Display Setting "MONO OFF" The monaural reception is OFF. "MONO ON" The monaural reception is ON. Disc Naming Power OFF Timer Setting the timer to turn this unit's power OFF automatically when Standby mode continues. Using this setting can save the vehicle's battery power. Display Setting "OFF – – –" Power OFF Timer function is OFF. "OFF 20M" Turns the power OFF after 20 minutes. (Original setting) "OFF 40M" Turns the power OFF after 40 minutes. "OFF 60M" Turns the power OFF after 60 minutes. — 17 — English English External view Number of items 2WARNING ..........................................If you connect the to the car chassis (ground), turn may start a fire. Always source running through the 1 .......................................... 2 2 .......................................... 1 3 The use of any accessories except for those provided might damage to the unit. Make sure only to use the accessories shipped the unit, as shown above. Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Cars with an ISO connector: Connect the speaker connector of the car to Connector B of the unit, and then connect the external power connector to Connector A. Cars without an ISO connector: First connect the wire of the wiring harness, and then connect the wiring harness connector to the unit. 4. Install the unit in your car. 5. Reconnect the - terminal of the battery. 6. Press the reset button. 2CAUTION • If your car is not prepared for this consult your Kenwood dealer. • Only use antenna conversion adapters antenna cord has an ISO plug. • Make sure that all wire connections are securely inserting jacks until they lock completely. • If your vehicle's ignition does not have an ACC ignition wire is connected to a power source with voltage such as a battery wire, the power will not be the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the unit's power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. — 18 — 18— 18 — —— Connecting Connecting Rear left output (White) Rear right output (Red) FM/AM antenna input TEL mute terminal Fuse (10A) Plug (page 20) Power Control terminal (page 21) Antenna Cord (ISO) Antenna Conversion Adaptor (ISO–JASO) (Accessory3) To Power Control terminal Special antenna adapter (Commercially available) For Volkswagen car Antenna Conversion Adaptor (ISO–JASO) (Accessory3) — 19— – + + + + + FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT. CONT — 19 — Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) - (To car chassis) Ignition key switch ACC 15 Car fuse box Battery Power control/ Motor antenna control wire (Blue/White) Connect either to the power control te...
