Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
A word “DUAL’ will appear on the display to indicate the dual-watch operation. c) Press the */ENT button “DUAL’ will disappear and the dual-watch will be cancelled. 29 a) i U C ~l ~i I I-I. LI LI 1 Lm_______I I light b) ^ DUAL ["“ (|^uncA+(^- ^ 'S.00 4 " ^¡im | |mg /C ~i ~i | |M( , u c i> n | ^_'z'-u_L:J lLl i-i-'LyJ displayed for displayed for app. 3 second app. 0.5 second NOTE: If no frequency has been stored in memory address number M1, the dual-watch operation is unavailable. You will hear a low-toned short beep when you press the 1/DUAL button informing you an incorrect entry. © Dual-watch on the dial-frequency and a memory frequency, (or call frequency) ( Procedure ) a) Recall a memory frequency you wish to use in the dual-watch. b) Press the 1/DUAL button while pressing the function button. A word “DUAL” will appear on the display to indicate the dual-watch operation. c) The display will alternately indicate the dial-frequency and a select memory frequency. a) R , u r ii n ] I light b) ▼ __J_____ DUAL | unwT I r-is.Q o _ j i’______I_______ I un _ _ _ I |M BBO _ _ _ I I I U 1 1 I 1 I I ■ I Li L J J I Li J =!■'-'j=Lj dJ-'-v----J dual-watch 30 NOTE: (1) If no frequency has been stored in memory, the dual-watch operation is unavailable. You will hear a low-toned short beep when you press the 1/DUAL button informing you an incorrect entry. (2) In dual-watch operation call frequency is considered as one of memory frequencies. That is, you can have dual-watch operation to listen on dial-frequency and call frequency. (3) Dual-watch on the dial-frequency and a memory frequency under scanning in sequence. ( Procedure) a) Set the Transceiver to the memory scan mode. b) Press the 1/DUAL button while pressing the Function button. A word “DUAL’ will appear on the display to indicate the dual-watch operation. The display will sequentially indicate the dial-frequency and the memory frequencies under scanning one by one. c) Press either the C/VSCAN button or */ MR /ENT button to cancel the dual-watch operation and to set the dial-frequency mode. The Transceiver will be set to either the dial-frequency mode or the memory mode depending on the condition at which the button is depressed. MR/ENT disappears r , I I r n n I II.U LI r I I !_/ L_ — 31 13 MHz Rotary Step — [A/MHz] ( Procedure) a) Press the “*/MR/ENT” key to set the status in VFO mode. b) Press the “A/MHz” the enable the MHz Rotary step function. c) Rotate the rotary channel to increase or decrease the operating frequency in MHz increment. d) Press “A/MHz” or“*/MR/ENT”to return to A/MHz VFO mode. down up MR/ENT 32 14 Changing the Frequency Step —[3/STEP Button] You can set the Transceiver’s step rate to 5kHz, 10kHz, 20kHz, 25kHz or 50kHz. ( Procedure) a) Press the 3/STEP button while pressing the Function. The frequency display will disappear and replaced by the current step rate. b) Rotate the rotary channel selctor. The six step rates will be sequentially indicated. of the dial-frequency will be shown in a small black box on the right side of the display. • The step rate is initially set to 10kHz at the factory. STEP c) Select the desired step rate. Then press the */ MR/ENT button to return to the previous dial-frequency. * b) (information) • When the step rate is set to 25kHz, 12.5kHz, the kHz digit dov 33 15 Battery-Save Function —[5/SAVE Button] This function allows you to reduce the current drain to 1/3 during receiver standby. The receiver will be activated once every single second. ( Procedure) a) Press the 5/SAVE button while pressing the Function button A “S” will appear on the display to indicate that the battery-save function is enabled. b) Press the 5/SAVE button again while pressing the Function button to release the battery saver. SAVE (( FUNC^ -t-fTf / /_/1 i I i I I I-I.LI LI T light ■ -s save CdUN^-ff /_/ /_ l I i I I -i. LI LI NOTE: The battery saver is disabled during dual-watch operation and scanning. 16 Frequency Lock —[6/LOCK Button] This feature allows you to lock the frequency and operating mode to prevent improper operation. You can also use this feature during scanning and dual-watch operation. ( Procedure) a) Press the 6/LOCK button while pressing the Function button A“FL’ will appear on the display to indicate that the frequency and operating mode is locked. b) Press the 6/LOCK button again while pressing the Function button to unlock them. <
Лодочное оборудование - AT-201 (1.49 mb)