Войти:
Оценок - 2, средний балл: 4.5 ( )

Инструкция по эксплуатации Attwood, модель 4202

Производитель: Attwood
Размер: 458.46 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Do not allow materials containing acetic acid (vinegar smell) such as silicone rubber sealant to contact the plastic parts of the pump. They may react with the plastic, causing cracks and pump failure. Notice: Discharge of oil prohibited. The Federal Water Pollution Control Act prohibits the discharge of oil or oily waste into the contiguous zone. Violators are subject to a penalty of $5,000. REQUIRED FOR INSTALLATION • Drill and suitable drill bits • Screwdriver and four #8 stainless steel pan head screws • Attwood thru-hull connector of appropriate size (if not already installed on boat; see chart) • Marine sealant • 1-1/8" (29mm) inside diameter smooth-bore hose of suitable length • Two appropriate hose clamps • 16-gauge wire, brown • 16-gauge wire, black • Attwood 2-Way Dash-Mounted Control Switch (Part No. 7615), 3-Way Switch (Part No. 7615A) • Fuse holder and appropriate fuse (see chart) • Two insulated terminal connectors for 16-gauge wire • Suitable materials to waterproof electrical connections If automatic operation is desired: • Attwood Automatic Float Switch, Part No. 4201 (with cover) or 4202 (without cover) • Shim for float switch mounting • Three additional #8 round-head stainless steel attaching screws The following materials are needed if no pump mounting pad is in place: • 1/2" (1.27 cm) thick marine plywood block large enough to mount pump (and automatic float switch, if used) • Hand-held roller • Fiberglass—18 oz. (.5kg) mat or woven roving • Polyester resin and catalyst MOUNTING PREPARATION Figure 1 1/2" (Minimum) Thick Mounting Pad Hose Thru-Hull Connector Hose Clamp • • • • • • • Water Line Hull 1. Choose a bilge pump mounting location in the lowest accessible part of the bilge. In this location, pump will remove the last 1" (2.54 cm) of standing water. Also, pump should be as close to the thru-hull connector as possible, for short discharge hose length. 2. To install mounting pad on fiberglass hull: Sand gelcoat or paint off the mounting surface to create an area that is 3" (7.6cm) wider than the mounting pad on each side. Completely cover the mounting pad with fiberglass. Saturate the fiberglass with resin, and press the fiberglass edges down against the hull to adhere the pad in place. Roll out the fiberglass to remove any uneven surfaces, air bubbles, or excess resin. To install mounting pad on aluminum hull: If your boat is not equipped with a bilge pump mounting pad we recommend that you consult your boat dealer or repair facility for instructions regarding fabrication and installation of a suitable mounting pad. PUMP MOUNTING INSTRUCTIONS Figure 2 LOCK • • • Locking Button Mounting Screws Retaining Tabs 1. Determine which direction you want pump outlet fitting to point after installation. Mark pump base and mounting pad in desired position. If Automatic Float Switch is to be installed, allow enough room on pad for shim and switch. 2. Remove pump base from motor housing by depressing lock button and twisting clockwise...

Эта инструкция также подходит к моделям:
Лодки - 4031 (458.46 kb)
Лодки - 69317 (458.46 kb)
Лодки - 4030 (458.46 kb)
Лодки - 4060 (458.46 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории