Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
If the manual relief valve is loosened (turned counterclockwise) when the outboard motor is tilted up, the outboard motor will suddenly tilt down. Be sure the valve is closed before operating the outboard motor. If the valve is not closed, the outboard motor will tilt up when operated in reverse. ENGINE COVER REMOVAL AND INSTALLATION (front) ENGINE COVER LATCH FIX UNLATCH (rear) UNLATCH FIX ENGINE COVER LATCH The engine cover latches fasten the engine cover to the outboard motor. To remove the engine cover, unlatch both front and rear latches, then lift the engine cover off the outboard motor. To install the engine cover, place the cover on the outboard motor, then latch both front and rear latches securely. SERVICING YOUR OUTBOARD MOTOR Engine Oil Level Check Check the engine oil level with the engine stopped and the outboard motor in the vertical position. 1. Unlatch and remove the engine cover (p. 70 ). 2. Remove the dipstick and wipe it clean. UPPER LIMIT LOWER LIMIT OIL LEVEL DIPSTICK 3. Insert the dipstick all the way in, then remove it and check the oil level shown on the dipstick. OIL FILLER CAP Running the engine with a low oil level can cause engine damage. 5. Install the oil filler cap and tighten it securely. 6. Install and lock the engine cover. 4. If the oil level is low, remove the oil filler cap, and add oil to reach the upper limit mark shown on the dipstick. Use the oil recommended on p. 74. SERVICING YOUR OUTBOARD MOTOR Engine Oil Change An engine oil evacuation device may be used to remove the engine oil. Drain the used oil while the engine is warm. Warm oil drains quickly and completely. 1. Unlatch and remove the engine cover (p. 70 ). Remove the oil filler cap. SCREW DRAIN BOLT COVER DRAIN BOLT COVER (oil drain guide) 2. Loosen the drain bolt cover screw 3. Place the drain bolt cover as using a flat blade screwdriver and shown to use it as an oil drain remove the drain bolt cover. guide. Place a suitable container under the guide. SERVICING YOUR OUTBOARD MOTOR DRAIN BOLT SEALING WASHER Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not discard it in a trash bin, dump it on the ground, or pour it down a drain. 4. Remove the engine oil drain bolt and washer. 5. Allow the used oil to drain completely, then install a new sealing washer on the engine oil drain bolt, and tighten it securely. 6. Reinstall the drain bolt cover. 7. With the outboard motor in a vertical position, fill to the upper limit mark on the dipstick (p. 71 ) with the recommended oil. Engine oil refill capacity: Without oil filter change: 2.1 US qt (2.0 ) With oil filter change: 2.2 US qt (2.1 ) 8. Install the oil filler cap and tighten it securely. 9. Install and lock the engine cover. X22ESR-UB (DENSO) DR7EB (NGK) 74 Engine Oil Recommendations Spark Plug Service SERVICING YOUR OUTBOARD MOTOR SPARK PLUG CAPS SPARK PLUGWRENCH Incorrect spark plugs can cause engine damage. Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil. SAE 5W-30 is recommended for general use. Honda recommends that you use API service category SG, SH or SJ oil with the ‘‘starburst’’ certification mark. The SAE oil viscosity and service category are in the API label on the oil container. RECOMMENDED SPARK PLUGS: Unlatch and remove the engine cover (p. ). Disconnect the spark plug caps from the spark plugs. Remove the spark plugs with a spark plug wrench. Inspect the spark plugs. Replace them if the electrodes are worn, or if the insulators are cracked or chipped. 2. 3. 2. 4. 70 .. .. .. .. .. 0.024 0.028 in (0.6 0.7 mm) 75 SERVICING YOUR OUTBOARD MOTOR SIDE ELECTRODE 0.024 0.028 in (0.6 0.7 mm) SEALINGWASHER INSULATOR Loose spark plugs can overheat and damage the engine. Overtightening the spark plugs can damage the threads in the cylinder head. Measure the spark plug electrode gap with a wire-type feeler gauge. Correct the gap, if necessary, by carefully bending the side electrode. The gap should be: Install the spark plugs carefully, by hand, to avoid cross-threading. After each spark plug seats, tighten with a spark plug wrench to compress the sealing washer. If reinstalling used spark plugs, tighten 1/8 1/4 turn after the spark plugs seat. If installing new spark plugs, tighten 1/2 turn after the spark plugs seat. Attach the spark plug caps. Install and lock the engine cover. 5. 6. 7. 8. 9. 76 Lubrication Points SERVICING YOUR OUTBOARD MOTOR PROPELLER SHAFT LOWER SWIVEL CASE UPPER SWIVEL CASE/ MOUNT FRAME TILT SHAFT TILLER HANDLE To prevent corrosion, apply anticorrosion oil to pivot surf aces where grease cannot penetrate. Apply Honda Marine Corrosion Inhibitor (or equivalent) to all areas under the engine cover and any exposed metal surfaces except the belts. Apply marine waterproof grease to the parts shown below: After the first 20 hours or ...
Эта инструкция также подходит к моделям:Лодки - BF50D (3.79 mb)