Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
To prevent personal injury, disconnect the power source when installing or servicing this product. Always remove the boat from the water before using 120V AC power tools. DO NOT use pump to remove gasoline, oil or other flammable liquids. Always use the fuse amperage rating specified for your pump model. Failure to do so could result in serious personal injury or fire hazards. Attwood bilge pumps are designed to exhaust STANDING WATER ONLY. They are not intended to prevent rapid accumulation of on-board water due to rough weather, hull damage, and/or other unsafe navigational conditions. Refer to Specification Chart to be sure you have selected the proper pump: 12-Volt Models ABYC Specifications ISO Specifications @13.6 VDC @12 VDC (GPH = Gal. Per Hour) (LPH = Liters Per Hour) Part Num./ Series Outlet Hose I.D. Motor Cart. Amp Fuse 0 ft. Head GPH/ amps 3.3 ft Head GPH/ amps 6.7 ft Head GPH/ amps 0kPa Head LPH/ amps 10kPa Head LPH/ amps Max Head (ft.@13.6v/ kPa@12v) 4606/600 3/4" 4620 2.5A 500/1.5 400/ 1.5 250/1.5 1705/1.3 1250/1.3 8'/27 4608/800 3/4" 4622 4A 800/3.0 660/3.0 510/3.0 2840/2.5 2274/2.5 14'/33 4612/1200 1-1/8" 4624 5A 1200/3.5 900/3.5 700/3.5 4169/3.0 3000/3.0 11' 7"/28 24-Volt Models ABYC Specifications ISO Specifications @24.0 VDC @24.0 VDC (GPH = Gal. Per Hour) (LPH = Liters Per Hour) Part Num. Series Amp Fuse 0 ft. Head GPH/ amps 3.3 ft Head GPH/ amps 6.7 ft Head GPH/ amps 0kPa Head LPH/ amps 10kPa Head LPH/ amps Max Head (ft.@24v/ kPa@24v) 4609/800 3/4" 4623 2A 800/1.3 660/1.3 500/1.3 2842/1.1 2160/1.1 14'/31 4613/1200 1-1/8" 4625 2A 1200/1.5 900/1.5 725/1.5 4100/1.3 3100/1.3 11'/28 MATERIALS REQUIRED • Three #8 stainless fasteners, suitable length for mounting surface • Cordless drill and 1/8" (3mm) bit • Hose clamps (Attwood # 9185, 2 per connection) • Mounting pad: marine plywood, fiberglass cloth and resin • Manual (# 7615A) or automatic float switch (#4201 or 4202) • Fuel-resistant, reinforced smooth bore outlet hose INSTALLATION LOCATION 1. Position pump in the lowest accessible part of the bilge. On sailboats, location should be centered over keel. (Figure 1) Thru-Hull Connector Hose & Clamp Hose MUST Rise Upward with NO DIPSuitable Mounting Pad Base Strainer 12" min. Above Water Line 2. Do not mount pump directly to hull. Attach base strainer to a marine plywood mounting pad that is fiberglassed to the hull. HOSE CONNECTION INSTRUCTIONS IMPORTANT: To prevent airlock, hose must rise continually upward to the thru-hull connector with no dips or sharp bends. Support hose if necessary. 1. Orient pump outlet for a direct, unobstructed hose path. 2. Secure all connections with hose clamps. 3. If no thru-hull connector exists, install at 12" min. (25mm) above water line. Apply marine sealant around thru-hull flanges on interior and exterior of hull. PUMP MOUNTING INSTRUCTIONS 1. To access mounting holes, remove base strainer. Hold housing with one hand, depress locking tab with other. Twist counter-clockwise and remove pump hou...
Эта инструкция также подходит к моделям:Лодки - Tsunami 4606 (459.93 kb)
Лодки - Tsunami 4608 (459.93 kb)
Лодки - Tsunami 4612 (459.93 kb)
Лодки - Tsunami 69390 (459.93 kb)