Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Follow the lettered and numbered instructions below to successfully install your DSR unit. The figure below illustrates one possible configuration. Figure 2.2: Basic DSR Configuration WARNING: To reduce the risk of electric shock or damage to your equipment- - Do not disable the power cord grounding plug. The grounding plug is an important safety feature. - Plug the power cord into a grounded (earthed) outlet that is easily accessible at all times. - Disconnect the power from the unit by unplugging the power cord from either the electrical outlet or the unit. 13579111315246810121416LAN100-240V , 1.0A, 50-60 HzDSR1161 ApplianceDigital UserServer 1Analog UserServers 2-16Configuration Portfor updatingfirmwareDSRIQModuleNetwork To install the DSR hardware: 1. Remove the DSR unit from the packing material. 2. Connect a terminal or PC running terminal emulation software (such as HyperTerminal) to the Configuration Port on the back panel of the DSR using the supplied null-modem cable. The terminal should be set to 9600 baud, 8 bits, 1 stop bit, no parity, no flow control. 3. Plug the supplied power cord into the back of the DSR unit and then into an appropriate power source. 4. When the power is switched on, the Power indicator on the front of the unit will blink for approximately 30 seconds while performing a self-test. Approximately 10 seconds after it stops blinking, press the Enter key to access the main menu. NOTE: The DSR unit may be rack mounted in a 1U configuration. The DSR does not support a 0U configuration. To configure the DSR hardware: 1. You will see the Terminal Applications menu with six options. Select option 1, Network Configuration. Figure 2.3: Network Configuration Menu 2. Select option 1 to set your network speed. When possible, you should set your connection manually without relying on the auto negotiate feature. Once you enter your selection, you will be returned to the Network Configuration menu. 3. Select option 2 and specify if you are using a static or BootP IP address. Avocent recommends using a static IP address for ease of configuration. If you are using a BootP address, please configure your BootP server to provide an IP address to the DSR, and skip to procedure C. 4. Select options 3-5 from the Terminal application menu in turn to finish configuring your DSR for IP Address, Netmask and Default Gateway. Once this is completed, type a O to return to the Main menu. To adjust the mouse acceleration: NOTE: We highly recommend that all Windows systems attached to the DSR use the default Windows PS/2 mouse driver. Before a PC running Windows NT or 2000 can be connected to the DSR, an adjustment to mouse acceleration must be made. Follow the steps below. For Windows NT (using default drivers): 1. From the Desktop, select Start - Settings - Control Panel – Mouse. 2. Click on the Motion tab. 3. Set the pointer speed to Slow. This will also need to be done for any NT user account that will be accessing the NT system through the DSR. For Windows 2000: 1. From the Desktop, select Start - Settings - Control Panel - Mouse. 2. Click on the Motion tab. 3. Set the Acceleration setting to none and the speed setting to the default of 50%. To connect a DSRIQ module to each server: 1. Locate the DSRIQ for your DSR unit. 2. Attach the appropriately color-coded ends to the keyboard, monitor and mouse ports on the first server you will be connecting to this DSR unit. 3. Attach one end of the CAT 5 cabling that will run from your DSRIQ to the DSR unit to the RJ45 connector on the DSRIQ. 4. Connect the other end of the CAT 5 cable to the desired port on the back of your DSR unit. 5. Repeat this step for all servers you wish to attach. NOTE: Power down the DSR unit before servicing. Always disconnect the power cord from the wall outlet. To connect the local port keyboard, monitor and mouse: (800, 1161 and 2161 models only) Attach your keyboard, monitor and mouse connectors to the appropriate ports on the back of your DSR unit. NOTE: You must install both a keyboard and mouse on the local port or the keyboard will not initialize properly. To connect and power up your DSR: 1. Connect your network cable from the LAN port on the rear of the DSR to your network. 2. Then power up all attached systems. NOTE: Your software registration key will be necessary for all installations. Internet Explorer 5.0 or higher must be installed on all systems running DSR software. To install your DS software: See the DS Installer/User Guide that ships with your software. 3 Local Port Operation Controlling your System at the Local Port17 Viewing and Selecting Ports and Servers17 Configuring OSCAR20 Resetting your Keyboard and Mouse26 Displaying Version Information27 Chapter 3: Local Port Operation Controlling your System at the Local Port The DSR800, 1161 and 2161 models include a local port on the back of the unit. This port allows you to connect a keyboard, monitor and mouse to the unit for direct access. The DSR uses OSCAR, our pa...
Эта инструкция также подходит к моделям:Ноутбуки - DSR2161 (1.65 mb)