Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Set the depth of cut by turning the handwheel (68) on the chip case. 3 Note: To compensate for possible play in the blade height setting mechanism, always raise the blade to the desired position. 7.3 Setting the saw blade tilt ADanger! Parts of the body or objects in the setting range can be caught by the running saw blade!Set the depth of cut only with the saw blade at standstill!! The saw blade tilt is steplessly adjustable between 0° and 45° . 1. Loosen twist handle (69) approx. one turn. 2. Set required blade tilt with the blade tilt lever (70). 3. Lock the set bevel angle by tightening the twist handle again. 7.4 Sawing with the rip fence 3 Note: When sawing with the rip fence the long fence extrusion must be used. 1. Adopting the fence extrusion to the workpiece height: . Wide edge (71) = for cutting thick stock . Small edge (72) = for cutting thin stock 2. The rip fence (73) is placed from top onto the guide extrusion (74) at the front of the saw and locked with the lock lever (75). ADanger! Always use the push stick if the distance between saw blade and rip fence is less than 120 mm. 3. Set the cutting height of the saw blade. The blade guard must rest with its front edge on the workpiece. 4. Set saw blade tilt and lock. 5. Start motor. 6. Cut workpiece in a single pass. 7. Switch machine off if no further cutting is to be done immediately afterwards. 7.5 Sawing with the mitre fence 1. Swing mitre fence on the table top. 2. Set to desired mitre angle and lock in that position. For mitre cuts, the fence extrusion is adjustable to 45° maximum. 67 66 68 69 70 71 72 73 74 75 23 ENGLISH A Caution! The plastic nose must have at least 10 mm distance to the line of cut. 3. Set the cutting height of the saw blade. 4. Set saw blade tilt and lock. 5. Start motor. 6. Cut workpiece in a single pass. 7. Switch machine off if no further cutting is to be done immediately afterwards. • Before cutting a workpiece to size make trial cuts on pieces of scrap. • Always place a workpiece on the saw table in such way that it can not tilt or rock (e.g. always place a curved board on the table with the convex side up). • When working long stock use suitable supports, such as table rear or side extensions (optional accessories). • Keep surfaces of the table top and table extension clean – in particular, remove resin residue with a suitable cleaning and maintenance spray (optional accessory). ADanger! Prior to all servicing: . switch machine OFF; . unplug power cable; . wait for saw blade to stop. • Check that all safety devices are operational again after each service. • Repair and maintenance work other than described in this section should only be carried out by qualified specialists. 9.1 Saw blade change ADanger! Directly after cutting the saw blade can be very hot – burning hazard! Let a hot saw blade cool down. Do not clean the saw blade with combustible liquids. Risk of injury, even with the blade at standstill. Wear gloves when changing blades. When fitting a saw blade, observe the direction of rotation! 1. Raise saw blade fully. 2. Remove blade guard. 3. Turn the flat head screw (76) of the table insert extrusion (77) clockwise by 1/4 turn and remove the table insert. 4. Loosen arbor bolt (78) with spanner (L.H. thread!). Hold outer blade collar (79) with ring spanner to counter. 5. Remove outer blade collar (79) and saw blade (80) from the saw spindle. 6. Clean clamping surfaces of saw spindle and saw blade. ADanger! Do not use cleaning agents (e.g. to remove resin residue) that could corrode the light metal components of the saw; the stability of the saw would be adversely affected. 7. Put on a fresh saw blade (observe direction of rotation!). ADanger! Use only suitable saw blades (see "Available accessories") – when using unsuitable or damaged blades parts could be explosive-like hurled from it by centrifugal force. Do not use: . saw blades made of high speed steel (HSS or HS); . saw blades with visible damage; . cut-off wheel blades. ADanger! . Mount saw blade only using genuine parts. . Do not use loose-fitting reducing rings; the saw blade could work loose. . Saw blades have to be mounted in such way that they do not wobble or run out of balance and can not work loose during operation. 8. Put on outer blade collar (79) (the inner blade collar's lug must engage in the groove of the outer blade collar). 9. Screw arbor bolt (78) back in the saw spindle (L.H. thread!) and tighten it. Hold outer blade collar (79) with ring spanner to counter. ADanger! . Do not extend arbor bolt tightening wrench. . Do not tighten arbor bolt by hitting the wrench. . After the arbor bolt has been tightened, remove all tools used during saw blade installation! 10. Fit table insert extrusion (81) flush into the saw table. 11. Turn the countersunk screw (82) counter-clockwise against the stop. 9.2 Cleaning the saw blade's height adjustment mechanism 1. Raise saw blade fully and dismount it (see "Saw blade change"). Now the spindle of th...