Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Recommended Minimum Wire Gauge for Extension Cords* Nameplate Extension Cord Length Amperes 25' 50' 75' 100' 150' 0 - 2.0 2.1 - 3.4 3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 16.0 16.1 - 20.0 18 18 18 18 16 14 12 18 18 18 16 14 12 10 18 18 16 14 12 10 18 16 14 12 10 16 14 12 12 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE. 8 Quik-Lok ® Blade Clamp • Periodically clean the Quik-Lok ® Blade Clamp with compressed air. • If the collar resists twisting, collar back and forth to shake loose. • Periodically lubricate Quik-Lok ® Blade Clamp with a dry lubricant such as graphite. Removing broken blades from the Quik-Lok ® Blade Clamp Unplug the tool before removing blades. Broken blades can be removed by the following methods. • Point the tool and shake the ( DO NOT turn the tool on while fingers are holding the open). The shank of the should drop out of the clamp. • If shaking the tool doesn't work... In most cases, a corner of the broken blade will extend beyond the blade clamp. Simply twist the collar and pull the broken blade out of the clamp by this corner. • If the broken stub doesn't extend far enough to be grabbed by its corner, use a thin blade with small teeth (such as a metal cutting blade) to hook the blade that is jammed in the clamp while twisting the collar and pull it out. OPERATION WARNING! To reduce the risk of injury, wear safety goggles or glasses with side shields. Adjustable Pivot Shoe (Fig. 3) The shoe can be adjusted forward or back-ward to six positions to take advantage of the unused portion of the blade or for spe-cial jobs requiring low blade clearance. DO NOT OPERATE SAWZALL WITHOUT SHOE. STRIKING THE SPINDLE AGAINST WORK MAY DAMAGE THE RECIPROCATING MECHANISM. 1/4 Turn Fig. 3 Impact Protection System WARNING! To reduce the risk of injury, be sure the blade always extends beyond the shoe and work throughout the stroke. Blades may shatter if they impact the work or shoe (Fig. 4). Fig. 4 Stroke Both models are equipped with a unique release lever down 1/4 turn and slide 1. To adjust the shoe, pull the shoe patented gearing system that provides efthe shoe forward or backward to the ficient power transmission and extended desired position. life in the most difficult cutting applications. This durable system will absorb impacts, 2. To lock the shoe in position, push the blade lock ups, and motor stalls. These shoe release lever up. models can be used for extreme cutting 3. After adjusting the shoe, slowly pull the applications such as large diameter pipe, trigger to be sure the blade always thick metal, pallets, and heavy demolition extends beyond the shoe and your and renovation work as well as for work throughout the stroke. general purpose cutting. 10 WARNING! Do not operate the Sawzallthe handle rotation button pressed in or with the handle locked into position. Rotating the Handle (Fig. 5) (Cat. No. 6523-21) The 6523-21 Orbital Super Sawzall® handle can rotate continuously in either direction, allowing the user to achieve optimal cutting positions and comfort. The handle can be locked into one of eight (8) detent positions, one at every 45° angle. To rotate the handle: 1. Unplug the tool. 2. Press in the handle rotation button. 3. Rotate the handle to the desired position. 4. Release the handle rotation button. This will lock the handle firmly into position. Note: Make sure the handle does not rotate before using the tool. Fig. 5 Starting, Stopping and Controlling Speed 1. To start the tool, grasp the handle firmly and pull the trigger. WARNING! If the handle can not be locked into position, do not operate the Sawzall®. Return the Sawzall® to a Milwaukee service facility immediately for repair. handle rotation button 2. To stop the tool, release Allow the tool to stop before removing partial cut or laying the Orbit Control Switch (Fig. The Orbital Super Sawzall ® is equipped with an orbit control switch. The be operated with straight reciprocating (non orbital) or orbital action. Straight reciprocating action should be used when a smooth cut is needed. Orbital action is recommended for fast, aggressive cutting. The optimal orbital action should be determined by the user for their specific cutting requirements. Fig. 6 2 1 1. For straight reciprocating action, move the orbit control switch to the straight cut symbol (1). 2. For orbital action, move the orbit control switch towards the orbital cut symbol (2). The amount of orbital action may be adjusted by moving the orbital control switch to any position between the two symbols. For larger orbital action, move the orbit control switch closer to the orbital cut symbol (2). For smaller orbital action, move the orbit control switch closer to the straight cut symbol (1). Orbital action may be adjusted when the tool is running. NOTE: Orbital action will not operate if the blade is installed upside down. 11 Selecting the The speed control strokes per minute. remain...
Эта инструкция также подходит к моделям:Лобзики и пилы - 6523-21 (1.09 mb)