Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
You will require a 13mm wrench or adjustable wrench (not supplied) for the lock nut (Fig. V) and the 6mm hex key for the set screws (Fig. W). Setting the fence square with the table 1. Make sure that the electrical plug is removed from the power point. 2. Push the saw arm (5) down to its lowest position and engage the release knob (6) to hold the saw arm in the transport position. 3. Loosen the mitre lock (25). 4. Rotate the table (21) until the pointer is positioned at 0.. 5. Tighten the mitre lock (25). 6. Using the 6mm hex key loosen the hex screw securing the top piece of the right hand side fence (Fig. X) and remove this top section. 7. Using the 6mm hex key provided, loosen the four screws securing the fence (19) to the base (Fig. Y). 8. Place a square against the fence (19) and alongside the blade (Fig. Z). 9. Adjust the fence (19) until it is square with the blade. 10. Tighten the screws securing the fence (19). 11. Loosen the Phillips head screw holding the pointer of the mitre scale (22) and adjust it so that it accurately indicates the zero position on the mitre scale (Fig. a). 12. Retighten the screw securing the mitre scale pointer. 13. Replace the top section of the fence and secure the hex screw using the 6mm hex key. Changing a blade DANGER! Never try to use a blade larger than the stated capacity of the saw. It might come into contact with the blade guards. Never use a blade X U Y V Z W 90° a that is too thick to allow the outer blade washer to engage with the flats on the spindle. It will prevent the blade screw from properly securing the blade on the spindle. Do not use the saw to cut metal or masonry. Ensure that any spacers and spindle rings that may be required suit the spindle and the blade fitted. 1. Make sure that the electrical plug is removed from the power point. 2. Push down on the operating handle (7) and pull the release knob (6) to disengage the saw arm (5). The release knob (6) can be turned so that it is held in the retracted position (Fig. b). 3. Raise the saw arm (5) to its highest position. 4. Using a Phillips head screwdriver loosen and remove the screw that secures the guard retraction arm (13) to the rotating blade guard (Fig. c). 5. Using a Phillips head screwdriver loosen (Fig. d) and remove the screw that secures the blade bolt cover (14). 6. Pull the rotating blade guard (12) down then swing it up together with the blade bolt cover (14). When the rotating blade guard (12) is positioned over the upper fixed blade guard (9) it is possible to access the blade bolt (Fig. e). 7. Hold the rotating guard (12) up and press the spindle lock button (26) (Fig. f). Rotate the blade until the spindle locks. 8. Use the 6mm hex key provided to loosen and remove the blade bolt. (Loosen in a clockwise direction as the blade screw has a left hand thread) (Fig. g). 9. Remove the flat washer and outer blade washer and the blade. 10. Wipe a drop of oil onto the inner blade washer and the outer blade washer where they contact the blade. 11. Fit the new blade onto the spindle taking care that the inner blade washer sits behind the blade (Fig. h). CAUTION. To ensure correct blade rotation, always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down. The direction of blade rotation is also stamped with an arrow on the upper blade guard. 12. Replace the outer blade washer (Fig. i). e f b g h c d 13. Depress the spindle lock button (26) and replace the flat washer and blade bolt. 14. Use the 6mm hex key to tighten the blade bolt securely (tighten in an anti-clockwise direction). 15. Lower the blade guard, hold the rotating lower blade guard (12) and blade bolt cover (14) in position and tighten the fixing screw (Fig. j). 16. Replace the guard retraction arm and secure onto the rotating blade guard (Fig. k). 17. Check that the blade guard operates correctly and covers the blade as the saw arm is lowered. 18. Connect the saw to the power supply and run the blade to make certain that it is operating correctly. Cross-cutting A crosscut is made by cutting across the grain of the workpiece. A 90. crosscut is made with the mitre table set at 0. (Fig. l). Mitre crosscuts are made with the table set at some angle other than zero. 1. Pull on the release knob (6) and lift the saw arm (5) to its full height. 2. Loosen the mitre lock (25). 3. Rotate the mitre table (21) until the pointer aligns with the desired angle. 4. Retighten the mitre lock (25). WARNING. Be sure to tighten the mitre lock before making a cut. Failure to do so could result in the table moving during the cut and cause serious personal injury. 5. Place the workpiece flat on the table with one edge securely against the fence (19). If the board is warped, place the convex side against the fence. If the concave side is placed against the fence, the board could break and jam the blade. 6. When cutting long pieces of timber, support the opposite end of the timber with the side support bars (32...
Эта инструкция также подходит к моделям:Лобзики и пилы - CDB305MS (1.27 mb)