Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at 1-800-397-1025. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating machine. Keep this information for future reference. Failure to comply any of the following safety procedures could result in serious personal injury. 1. To prevent the possibility of electrical shock, do not immerse machine in water or permit liquids to spill inside. 2. Do not allow articles of clothing (neckties, scarves, papers, etc.) near front or rear machine openings as they could get caught by rollers and be pulled inside, causing personal injury. 3. Do not insert sharp objects into front or rear machine openings. Do not place anything in feed tray openings of machine other than appropriate laminating materials or pouches. 4. Do not attempt to laminate items that exceed total recommended material thickness. 5. Do not operate machine for any other purposes than its intended use. 6. Do not operate machine if electrical plug or power cord is damaged. 7. Turn off the power when unattended or not in use. Unplug machine before moving it or when it is not in use for an extended period of time. 8. This machine is intended for indoor use only. 9. Do not alter or extend electric plug. Plug is configured for appropriate electrical supply. 10. The socket-outlet shall be installed near the equipment and shall be easily accessible. - 3 CHARACTERISTIC RS Roll Laminator Line is advanced laminators with time transcendental design, utilizing the latest in laminating technology. It is designed for you to set temperature and speed as necessary and have the machine remember your settings. Also, you can laminate anything at high speed, regardless of thickness of material and type of film. Remote control device allows for control of the machine from the front or rear. Foot-Pedal Switch allows for hands-free operation. It is also designed for convenient use by anyone through the simple procedure of adjusting film tension in accordance with the thickness of film and materials to be laminated. SPECIFICATIONS Description RSH-1650 RSR-1050 RSH-1050 RSR-685 Dimensions(w x d x h) 1960x650x1210mm (77.2x25.6x47.4in) 1400x650x1220mm (55.1x25.6x48.0in) 1070x650x1220mm (42.1x25.6x48.0in) Weight 300Kg (660lbs) 140Kg (308.6lbs) 100Kg (220.5lbs) Voltage/Cycles AC100~120V, 50/60Hz AC220~ 240V, 50/60Hz Power Consumption 3300w 3000w 2000w Max. Laminating Speed 2m/min 6.5ft/min 13.1ft/min 4m/min 6.5ft/min 2m/min 4m/min 13.1ft/min Max. Laminating Width 1650mm (64.9inch) (41.3inch) 1050mm 685mm (27inch) Max. Laminating Thickness 15.0mm (0.6inch) 13.0mm (0.5inch) Film thickness 32 - 250micron (1.3-10mil) COLD and WARM Laminating Yes Yes Yes Cooling Blowers 3 2 1 Take-Up Yes Yes Yes Film Alignment No Yes Yes Cutter-Cross Yes Yes Yes Ass'y Stand Yes Yes Yes Switch-Foot Yes Yes Yes Wired Remote Control Yes Yes Yes - 4 NAMES OF MAJOR PARTS OF MACHINE 61432410111257891 NO PART NAME RSH-1650 RSH-1050 RSR-1050 RSR-685 1 FRAME-GUIDE,PAPER 0 0 0 0 2 TAKE-UP SWITCH 0 0 0 0 3 TAKE-UP BOBBIN 0 0 0 0 4 IDLE BAR 0 0 0 0 5 TABLE-FRONT 0 0 0 0 6 HOT ROLLER 0 0 X X HOT METAL ROLLER X X 0 0 7 ASS'Y-STAND 0 0 0 0 8 FOOT SWITCH 0 0 0 0 9 REMOTE CONTROL SWITCH 0 0 0 0 10 CONTROL PANEL 0 0 0 0 11 PRESSURE LEVER 0 0 0 0 12 TENSION CONTROL KNOB 0 0 0 0 13 FILM ALIGNMENT KNOB X 0 0 0 14 SAFETY COVER 0 0 0 0 - 5 How to install the rewinder 1. Disassemble both the Right cover and the Left cover. (Note :Turn the fastening nut of the Emergency switch counterclockwise and disaasemble the Emergency switch before disassembling the Right cover.) 2. Disassemble the Rear cover. 3. Disassemble the power switch bracket which is located at the left side of the machine. M5 screw 6EA Power switch bracket Plate-Rewinder L 4. Put the Plate-Rewinder L on the outer side of the frame as shown in the following figure and fasten it with six M5 screws. 5. Put the Plate-Rewinder R on the outer side of the frame as shown in the following figure and fasten it with six M5 screws. Plate-Rewinder R - 6 - 6. Insert the male connector from the Rewinder motor into the female connector from the take -up motor. Female Connector from take-up motor Male Connector from rewinder motor 7. Assemble the Right cover letting the wires go through the slot which is located at the rear side of the Right cover. 8. Put the Power switch bracket on the Plate-Rewinder L and fasten it with two M4 screws. Power switch bracket Plate-Rewinder L How to install the unwinder - 7 1. Put the Plate-Unwinder R on the inner side of the frame as shown in the following figure and fasten it with four M6 hexagonal bolts. 2. Put the Plate-Unwinder L on the inner side of the frame as shown in the following figure and fasten...
Эта инструкция также подходит к моделям:Ламинаторы - 1650 (1.41 mb)
Ламинаторы - RSH-1050 (1.41 mb)
Ламинаторы - RSR-685 (1.41 mb)