Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
(Note :Turn the fastening nut of the Emergency switch counterclockwise and disaasemble the Emergency switch before disassembling the Right cover.) 2. Disassemble the Rear cover. 3. Disassemble the power switch bracket which is located at the left side of the machine. M5 screw 6EA Power switch bracket Plate-Rewinder L 4. Put the Plate-Rewinder L on the outer side of the frame as shown in the following figure and fasten it with six M5 screws. 5. Put the Plate-Rewinder R on the outer side of the frame as shown in the following figure and fasten it with six M5 screws. Plate-Rewinder R - 6 - 6. Insert the male connector from the Rewinder motor into the female connector from the take -up motor. Female Connector from take-up motor Male Connector from rewinder motor 7. Assemble the Right cover letting the wires go through the slot which is located at the rear side of the Right cover. 8. Put the Power switch bracket on the Plate-Rewinder L and fasten it with two M4 screws. Power switch bracket Plate-Rewinder L How to install the unwinder - 7 1. Put the Plate-Unwinder R on the inner side of the frame as shown in the following figure and fasten it with four M6 hexagonal bolts. 2. Put the Plate-Unwinder L on the inner side of the frame as shown in the following figure and fasten it four M6 hexagonal bolts. SETTING UP FILM . . L . . C . . D . . . . . . . . . . . . M6 hexagonal bolt Plate-Unwinder R - 8 - 1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like picture 4 and 5, adhere core closely. (Make the right/left direction of fixing screw consistent.) 5. Locate film in the middle, and then fasten core fixing screw. HANGING FILM Picture 1 Upper Film Lower Film Upper Film Lower Film Picture 2 Picture 3 Picture 4 Picture 5 Core Fixing Screw - 9 - 1. HOT FILM LOWER ROLL FILM LOWER ROLL FILM UPPER ROLL FILM UPPER IDLE BAR HOT ROLLER HOT METAL ROLLER LOWER IDLE BAR UPPER ROLL FILM UPPER IDLE BAR ROLLER RSH-1050/1650 RSR-685/1050 1. Insert bar into the core of the roll film then place the bar on the machine. 2. Place the Pressure Lever (on the right side of machine) to the open mode at 15mm. 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers. 4. Pull the film from the upper roller passing over the upper idle bar to the upper roller and put it on the roller. 5. When temperature reaches 80.(176°F), resin starts melting and films turn to be transparent. 6. Place the film from lower shaft beneath the film from the upper roller which is already melting and unwind films of both rollers 30~40Cm(1~1.3ft) for loosing the tension. 7. Set the pressure Lever to the 1mm. 8. Set speed at 1 and press Run button. The films will be fed into the machine and will come out from the rear site of machine. 9. Check the status of lamination and place the pressure lever at lamination mode. 2. COLD FILM TAKE UP DEVICE TAKE UP DEVICE - 10 COLD FILM COLD FILM RSH-1050/1650 RSR-685/1050 1. Set up cold film below the upper bar of the machine (Set the same as method of HOT film for protect paper of lower part) 2. Set the pressure Lever to the 15mm, open mode 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers 4. Pull the film from the upper roller passing over the upper idle bar to the upper roller and put it on the upper roller. 5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back. 6. Allow some of the film with melted resin to stick to the Guiding Paper. 7. Place the film from lower shaft beneath the film from the upper roller which is already melting and unwind films of both rollers 30~40Cm(1~1.3ft) for loosing the tension. 8. Set the pressure Lever to the 1mm 9. Set speed at 1 and press Run button. The films will be fed into the machine and will come out from the rear site of machine 10. Check the status of lamination and place the pressure lever at lamination mode CONTROL OF ROLLER PRESSURE TAKE UP DEVICE PAPER BACK COLD FILM UPPER IDLE BAR LOWER IDLE BAR HOT ROLLER PAPER BACK UPPER IDLE BAR PAPER BACK LOWER IDLE BAR HOT METAL ROLLER TAKE UP DEVICE COLD FILM ROLLER PAPER BACK - 11 - ***Methods of controlling pressure of the roller** 1. For setting, pull the pressure lever out and turn the lever to following the indication 2. Open/15mm : for laminating 15mm(0.6") thick board (RSH-1050/1650) 3. 10~13mm : for laminating 10~13mm(0.4" to 0.5") thick board 4. 5~7mm : for laminating 5~7mm(0.2" to 0.27") thick board 5. 1mm : for laminating 1mm(40mil) thick board 6. LAMINATING : for laminating 32~250micron thick film INSTRUCTIONS FOR CONTROL PANEL We designed this machine standing by user’s convenience. You can manipulate - 12 speed and temperature of rollers each by each by the LCD controller. And with memory function, you d...
Эта инструкция также подходит к моделям:Ламинаторы - 1050 (1.41 mb)
Ламинаторы - RSH-1050 (1.41 mb)
Ламинаторы - RSR-685 (1.41 mb)