Войти: (During operation, it is always ON) • QUIET can't be selected in FAN MODE. • Sleep-timer can't be used. And you can't use both wired remote control unit and wireless simultaneously. (Only one kind can be selected) En-3 Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 MANUAL AUTO button When kept on pressing the MANUAL AUTO button for more than 10 seconds, the forced cooling operation will start. The forced cooling operation is used at the time of installation. Only for authorized servic
P/N9368987022 FUJITSU GENERAL LIMITED CONTENTS SAFETY PRECAUTIONS ....................................... 1 NAME OF PARTS ................................................... 2 PREPARATION ....................................................... 3 OPERATION ........................................................... 3 TIMER OPERATION (OFF TIMER/ON TIMER) ...... 5 TIMER OPERATION (WEEKLY TIMER) ................. 6 ENERGY SAVE OPERATION ............................... 11 ADJUSTING THE DIRECTION OF A
When the forced cooling operation starts by any chance, press the START/STOP but- ton to stop the operation. 3Indicator (Fig. 3) 4Remote Control Signal Receiver 5OPERATION Indicator Lamp (red) 6TIMER Indicator Lamp (green) If the TIMER indicator lamp flashes when the timer is operating, it indicates that a fault has occurred with the timer setting (See Page 14 Auto Restart). 7SUPER QUIET Indicator Lamp (green) 8COIL DRY Indicator Lamp (orange) 9Intake Grille (Fig. 4) 0Front Panel AAir Filter B
6 M). Each time the button is pressed, the fan speed changes in the following order: AUTO HIGH MED LOW QUIET About three seconds later, the entire display will reappear. When set to AUTO: Heating : Fan operates so as to optimally circulate warmed air. However, the fan will operate at very low speed when the temperature of the air issued from the indoor unit is low. Cooling : As the room temperature approaches that of the thermostat setting, the fan speed becomes slower. Fan : The fan runs at the
(The monitor operation range is ±4 °F relative to the thermostat setting.) . If the mode automatically selected by the unit is not satisfactory, see page 3 for instructions on changing the mode setting (HEAT, COOL, FAN). * Heating: . Use to warm your room. . When Heating mode is selected, the air conditioner will operate at very low fan speed for about 3 to 5 minutes, after which it will switch to the selected fan setting. This period of time is provided to allow the indoor unit to warm up befor
Description Part No. Ord. Q'ty ASU30CLX ASU36CLX 1 FRONT PANEL TOTAL ASSY 9315335036 9315335036 2 INTAKE GRILLE ASSY 9315336026 9315336026 4 AIR FILTER 9315014016 9315014016 5 CLAMPER(GRILLE) 9306755010 9306755010 6 RECEIVER WINDOW 9315010018 9315010018 8 CROSSFLOW FAN ASSY 9315024015 9315024015 9 BEARING C ASSY 9306628017 9306628017 10 CASING ASSY 9315331021 9315331021 22 R AND L LOUVER 9311997016 9311997016 23 SPACER B 9312441013 9312441013 26 DRAIN CAP 9367677009 9367677009 27 EVAPORATOR ASSY
THERMISTOR THE SWITCH FOR OPENING AND CLOSING OF A PANEL POWER SUPPLY CIRCUIT REMOTE CONTROL COMMUNICATION K1 DW12D1 K1-4 4 1 3 2 6 5 4 3 2 1 5 4 3 2 1 6 5 4 3 2 1 CN8 DIFFUSER CN2 RIGHT / LEFT UP / DOWN CN5 W5 TM4 C13 0.01 250V C14 0.01 250V PIPE TEMPERATURE CN3 1 2 (36) (37) 1 3 L6 BLm18
To confirm settings Press the TIMER MODE button once. (The timer setting information will be displayed for 15 seconds after the TIMER MODE button is pressed.) . To change settings Confirm the settings as noted above, then press the SET TIME button and TIMER MODE button as necessary to change the desired timer setting. (The timer settings will be displayed for 15 seconds after the button is pressed.) . After confirming or changing the settings, press the START/STOP button to start operation. To C
