Оценок - 4, средний балл: 3.8
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
If necessary, set the air conditioner on before you wish to use the room. Frost When outside temperatures are low and humidity is high, frost may form in the outdoor unit when heating is selected. If this happens: ♦ The heating operation is stopped. ♦ The Deice mode is triggered automatically for about seven minutes. No intervention is required from you; after about seven minutes, the air conditioner starts operating again normally. High indoor and outdoor If both the indoor and outdoor temperatures temperatures are high and you select the Heat mode, the outdoor unit's fan and compressor may stop at times. This is normal; simply wait until the air conditioner switches on again. Power failure If a power failure occurs when the air conditioner is operating, the unit is switched off. When the power returns, the air conditioner starts up again automatically. e-21 ENGLISH Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used. If the air conditioner is used at... Then... High temperatures The automatic protection feature may be triggered and the air conditioner stopped. Low temperatures A water leak or some other malfunction may occur if the heat exchanger freezes. High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for long periods. Mode Outdoor Temperature Indoor Temperature Indoor Humidity Heating 0°C to 24°C approx. 27°C or less -Cooling 21°C to 43°C approx. 18°C to 32°C approx. 80% or less Drying 18°C to 43°C approx. 18°C to 32°C approx. - # If the outdoor temperature is as low as 0°C, the heating capacity drops up to 70~80% depending on the operating condition. If the cooling operation is used at over 33°C(indoor temperature), it does not cool at its full capacity. Operating Your Air Conditioner Without the Remote Control Your air conditioner can be operated directly from the indoor unit if the remote control is lost or broken. 1 Slide the lower front grille down. 2 To switch the air conditioner on, press the ON/OFF switch on the right side of the indoor unit. Result: ♦ The OPERATION indicator on the indoor unit comes on. ♦ The indoor unit beeps. ♦ The air conditioner starts up in the most suitable mode for the room temperature: Room Temperature Operating Mode Less than 21 °C Heat 21°C or above Cool 3 To switch the air conditioner off, press the ON/OFF switch again. Note Even if the air conditioner has been switched on via the ON/OFF switch, operations can still be controlled using the remote control as usual. 1 e-22 Solving Common Problems Before contacting the after-sales service, perform the following simple checks. They may save you the time and expense of an unnecessary call. Problem Explanation/Solution The air conditioner does not operate at all ♦ Check that the breaker used for the air conditioner is switched on. ♦ Check that the operation indicator on the indoor unit is on; if necessary press the (5) (On/Off) button on the remote control. ♦ Check whether the TIMER indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 18 and 19 for further details) The air conditioner does not operate with the remote control ♦ Check that there are no obstacles between you and the indoor unit. ♦ Check the remote control batteries. ♦ Check that you are close enough to the indoor unit (seven meters/yards or less). No beep is heard when you press the (5) (On/Off) on the remote control ♦ Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit. ♦ Replace the remote control batteries if necessary. The air conditioner does not cool or heat ♦ Check that the correct operating mode has been selected (AUTO, COOL, HEAT). ♦ The room temperature may be too low or too high. ♦ Dust may be blocking the air filter guard; refer to page 24 for cleaning instructions. ♦ Check that there is no obstacle in front of the outdoor unit. When heating, the required room temperature is never reached and the air conditioner frequently stops ♦ Check that the required temperature has been set correctly. ♦ Increase the fan speed. ♦ If the air flow is directed upwards, use the remote control to direct it downwards. The fan speed does not change when you press the ^ (§(( ( button ♦ Check that the operating mode is set to COOL, HEAT or FAN ; in the AUTO mode, the fan speed changes automatically and in the DRY mode, it is set to AUTO. The air flow direction does ♦ Check that the air conditioner has been switched on; if necessary, not change when you press the press the (S) (On/Off) button on the remote control. button The timer is not correctly triggered ♦ Check that the timer has been programmed correctly; see pages 18 and 19. Odour is permeated in the room during air conditi...
Эта инструкция также подходит к моделям:Кондиционеры - AQ18P0GED5/UPA (6.48 mb)
Кондиционеры - AQ18P0GED6/SAR (6.48 mb)
Кондиционеры - AQ24P6GED5/UPA (6.48 mb)
Кондиционеры - AQ24P6GED6/SAR (6.48 mb)