Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
7. R RRe eea aar rr A AAm mmp ppl lli iif ffi iie eer rr O OOu uut ttp ppu uut tt - These are output jacks for sending the audio signal to the rear amplifier. 8. S SSu uub bbw wwo ooo oof ffe eer rr A AAm mmp ppl lli iif ffi iie eer rr O OOu uut ttp ppu uut tt - These are output jacks for sending the audio signal to the subwoofer amplifier. 9. S SSo oou uur rrc cce ee 2 22 I IIn nnp ppu uut tt - This is the input for the secondary source unit. 10. S SSo oou uur rrc cce ee 1 11 I IIn nnp ppu uut tt - This is the input for the main source unit. © 2002 Directed Electronics, Inc FIGURE 1—REAR PANEL 1234 5 6 78910 INTIIAL SETTINGS 1. Make sure the main Source 1 unit is connected to the Source 1 inputs, then adjust the main source units volume to just below maximum. 2. Adjust the Source 1 input gains (top of unit) to the minimum setting and the 2500 master volume control to the maximum setting. N NNO OOT TTE EE: ::If connecting more than one input source to the 2500, use the Source 1 gain controls to match the input level of both sources. 3. Set the subwoofer controls and filter gain controls to the flat (center) setting. 4. Complete all signal and power connection to the 2500. 5. Turn the system on and increase the gain on the source one inputs until audible distortion can be heard. The system should be very loud at this time. 6. Reduce the 2500 master volume level and test for well balanced and linear volume adjustment when using the 2500 master volume control. 7. When connecting a second source unit to the Source 2 input, the source one input gains (top of unit) may need further adjusting to achieve a close signal level match. © 2002 Directed Electronics, Inc CROSSOVER AND FILTER ADJUSTMENTS The crossover and filter gain adjustments can be performed two different ways, by using a piece of audio test equipment called an RTA (Real Time Analyzer) or by listening to a familiar piece of music. The RTA is most commonly used to achieve the flattest possible system response in preparation for a sound off competition. Although an RTA may help in setting a flat system response it does not ensure the unit is tuned for your personal listening preferences. When setting the 2500 filter and gain controls using a familiar piece of music, adjustments can be made according the way you like the music to sound in relation to the vehicles acoustics and the type of drivers in the system. 1. Leave the subwoofer controls and the five filter gain controls to the flat (center) position. 2. If the dedicated subwoofer output is being used, turn off any active CONTROL PANEL FEATURES 1. M MMa aas sst tte eer rr V VVo ool llu uum mme ee/ //F FFa aad dde eer rr C CCo oon nnt ttr rro ool ll - The master volume/fader control knob is a retractable dual-function control that extends when needed for adjustments and retracts when not in use. To extend and retract the knob, press and release it into the subwoofer crossovers in the subwoofer amplifier. N NNO OOT TTE EE: ::When interfacing with Directed class d amplifiers with non-defeatable Low-pass crossovers adjust the amplifiers crossover point to its highest frequency setting. 3. Adjust the crossover point and subwoofer volume using the subwoofer controls (knobs four and five on the front panel) so the subwoofer blends with the satellite speakers. When set properly the bass should not be localized and voices should not be heard through the subwoofers. 4. Fine tune the system sound using the subwoofer volume control and the five filter gain controls for different tastes or audio material. 5. After adjusting the system for the best sound quality use the equalizers master volume to adjust overall volume of the system. control panel; it will extend or retract with each press. V VVo ool llu uum mme ee - The master volume/fader control knob is set to the volume position when it is initially extended. It controls the overall © 2002 Directed Electronics, Inc volume of the system and affects all line level outputs to the amplifiers. F FFa aad dde eer rr -To set the master volume/ fader control knob to the fader position, pull gently on it until a notched position is reached. It will then control the front-to-rear balance of the front and rear RCA output jacks. W WWA AAR RRI IIN NNG GG! !!DO NOT use excessive force when using this knob or damage to its release mechanism may result. 2. P PPo oow wwe eer rr O OOn nn/ //O OOf fff ff L LLE EED DD - This LED will be illuminated when the 2500 is on. 3. I IIn nnp ppu uut tt S SSo oou uur rrc cce ee S SSw wwi iit ttc cch hh - The input source switch selects between Source 1 and Source 2 inputs. FIGURE 2—CONTROL PANEL 4 S SSu uub bbw wwo ooo oof ffe eer rr V VVo ool llu uum mme ee C CCo oon nnt ttr rro ool ll: The subwoofer volume control knob controls the volume of the dedicated subwoofer output. 5. S SSu uub bbw wwo ooo oof ffe eer rr F FFr rre eeq qqu uue een nnc ccy yy C CCo oon nnt ttr rro ool ll - The subwoofer frequence control knob controls the low-pass c...