Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
The unit is designed to operate with approximately 1/2" of water in bottom pan. 4. Pull the bottom window sash down behind the Top retainer bar until they meet. NOTE: 1. Do not pull the window sash down so tightly that the movement of Frame curtain is restricted. Attach the cabinet to the window stool by driving the screws (Type B) through the cabinet into window stool. 2. The cabinet should be installed with a very slight tilt downward toward the outside. SupportBracket Lock nut Sill Bracket CarriageBolt (M-Screw) Front angle Window stool Window sash Top retainer bar Cabinet Foam-PE Frame curtain Screw(Type B) Front Angle Sash track Foam-PE Cabinet Track hole SupportBracket Carriage boltand lock nut Machine screw(Type D) and lock nut Outer edgeof window sill Screw(Type B) Sill bracket Top retainer bar Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 12 Power Cord Screw Screw (Type A) Window locking bracket Foam-Strip Screw(Type C) 5. Pull each Frame curtain fully to each window sash track, and pull the bottom window sash down behind the Top retainer bar until it meets. 6. Attach each Frame curtain the window sash by using screws (Type C.) (See Fig. 10) 7. Slide the unit into the cabinet.(See Fig. 11) CAUTION: For security purpose, reinstall screws(Type A) at cabinet's sides. 8. Cut the Foam-strip to the proper length and insert between the upper window sash and the lower window sash.(See Fig. 12) 9. Attach the Window locking bracket with a screw (Type C.) (See Fig. 13) 10. Attach the front grille to the cabinet by inserting the tabs on the grille into the tabs on the front of the cabinet. Push the grille in until it snaps into place.(See Fig.14) 11. Lift the inlet grille and secure it with a screw (Type A) through the front grille.(See Fig. 14) NOTE: Please refer p.6 for setting ventilation kit. 12. Window installation of room air conditioner is now completed. See ELECTRICAL DATA for attaching power cord to electrical outlet. Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 13 Features and Installation Electrical Data(For 115V model only) Line Cord Plug Use Wall Receptacle Power Supply Do not under any circumstances cut or remove the grounding prong from the plug. Power supply cord with 3-prong grounding plug Standard 125V, 3-wire grounding receptacle rated 15A, 125V AC Use 15 AMP. time delay fuse or 15 AMP. circuit breaker. USE OF EXTENSION CORDS Because of potential safety hazards, we strongly discourage the use of an extension cord. However, if you wish to use an extension cord, use a CSA certified/UL-listed 3-wire (grounding) extension cord, rated 15A, 125V. Electrical Data(For 230/208V model only) Line Cord Plug Use Wall Receptacle Power Supply Do not under any circumstances cut or remove the grounding prong from the plug. Power supply cord with 3-prong grounding plug Standard 250V, 3-wire grounding receptacle rated 15A, 250V AC Use 15 AMP. time delay fuse or 15 AMP. circuit breaker. Do not under any circumstances cut or remove the grounding prong from the plug. Power supply cord with 3-prong grounding plug Standard 250V, 3-wire grounding receptacle rated 20A, 250V AC Use 20 AMP. time delay fuse or 20 AMP. circuit breaker. Before you call for service... All wiring should be made in accordance with local electrical codes and regulations. NOTE : Aluminum house wiring may pose special problems. Consult a qualified electrician. ELECTRICAL SAFETY IMPORTANT GROUNDING INSTRUCTIONS Air conditioner has a three-prong grounding plug on its power supply cord, which must be plugged into properly grounded three-prong wall receptacle for your protection against possible shock hazard. 230, 208, and 230/208 VOLT UNITS These units are equipped with a three-prong grounding plug on the power supply cord, which must be plugged into a matching properly grounded three-prong wall receptacle for your protection against possible shock hazard. If such an outlet is not present, one must be installed by a qualified electrician in accordance with the National Electrical Code and local codes and ordinances. NOTE: DO NOT USE AN EXTENSION CORD ON 230, 208, AND 230/208 VOLT UNITS. 14 Before you call for service... Troubleshooting Tips Save time and money! Review the chart below first and you may not need to call for service. Normal Operation • You may hear a pinging noise caused by water being picked up and thrown against the condenser on rainy days or when the humidity is high. This design feature helps remove moisture and improve efficiency. • You may hear the thermostat click when the compressor cycles on and off. • Water will collect in the base pan during high humidity or on rainy days. The water may overflow and drip from the outdoor side of the unit. • The fan may run even when the compressor does not. Abnormal Operation Problem Possible Causes What To Do Air conditioner does not start The air conditioner is unplugged. The fuse is blown/circuit breaker is tripped. Power failure. • Make sure the air conditioner plug is pushed completely in...