Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the planer is installed and running properly. Compare the contents of your container with the following parts list to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. NOTE: To remove the box from atop the planer table, loosen the table lock handle, push in the elevating handwheel (see Figure 3) and rotate the handwheel to lower the table. Contents of the Shipping Container 1 Planer 1 Dust Hood - (A) 4 Foot Pads - (B) 1 Air Impact Screwdriver - (C) 1 RA-30E 460V Overload Relay - (D) 5 Star Point Screwdrivers - (E) 1 Breaker Bar - (F) 1 Air Valve - (G) 1 Air Valve Mounting Bracket - (H) 1 Air Valve Pressure Gauge - (J) 20 Flat Head Spline Socket Screws, M6x14 - (K) 10 Spline Bits, T-20 - (L) 10 Replacement Knife Inserts - (M) 1 Handle with Knob - (N) 3 Open End Wrenches, 17-19, 22-24, and 1214 mm - (O) 1 Reversible Screwdriver - (P) 4 Hex Wrenches, 3, 4, 5, and 8mm - (R) 8 Button Head Socket Screws, M6x12 - (S) 8 Lock Washers, M6 - (T) 8 Flat Washers, M6 - (U) 1 Operating Instructions and Parts Manual 1 Warranty Card Awarning Read and understand the entire contents of this manual before attempting set-up or operation! Failure to comply may cause serious injury. 8 Installation and Assembly Tools Required for Installation: Forklift or hoist, with lifting straps 4mm hex wrench (provided) 22mm combination wrench (provided) Remove any straps or boards holding the planer to the pallet. Place straps under the four lifting hooks at front and back to raise the planer off the pallet and move it to location. Acaution Make sure the straps will not damage buttons or levers on the front of the planer. The planer should be installed on a solid foundation, preferably a concrete floor. The machine area should be clean, dry, well ventilated, and well lit. Since planers can create noise problems, the site selection should be one which minimizes reverberant sound from walls, ceilings and other equipment. Electricals should be installed so that they are protected from damage and exposure. Be sure to properly ground the machine. Lower the leveling screws, and place the four foot pads beneath the leveling screws. See Figure 1. Lower the machine slowly onto the foot pads. The screws can be turned as necessary until the planer table is level. Tighten the hex nuts against the base to secure the screw settings. Exposed metal parts have been coated with a rust preventative. This should be removed with a soft cloth moistened with kerosene or a good commercial cleaner/degreaser. Do not use an abrasive pad, and do not get solvents near plastic parts or painted areas. Figure 1 Dust Hood Use a 4mm hex wrench to mount the dust hood to the planer with eight M6 x 12 button head socket screws, eight M6 lock washers and eight M6 flat washers, as shown in Figure 2. It is strongly recommended that a dust collection system be used with this machine. It should be of sufficient volume for this size planer. If a dust collector is not used, the user is cautioned against the health hazard and the limitations in the OSHA regulation for employee or student exposure to dust particles. Figure 2 9 Grounding Instructions Awarning Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be properly grounded to help prevent electrical shock and possible fatal injury. This machine must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes, is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Repair or replace a damaged or worn cord immediately. Make sure the voltage of your power supply matches the specifications on the motor plate of the Planer. The machine should be connected to a dedicated circuit. The use of an extension cord is not recommended for the WP2510 Planer. 230 Volt Operation The Planer is factory wired for 230 volt, but can be converted to 460 volt if so desired (see “Converting From 230 Volt to 460 Volt”). You may either install a plug or “hard-wire” the Planer directly to a control panel. If you are connecting a plug, use a proper UL/CSA listed 3-pole, 4-wire grounding plug suitable for 230 vol...