Оценок - 1, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
This option is not set by default. Password Changes Enables or disables the user from changing the system password without the administrative password. This option is enabled by default. TPM Security Enables or disables the trusted platform module (TPM) security. You can set the TPM security to: Deactivate (default) Activate Clear NOTE: When TPM Security is set to Clear the system setup program clears the user information stored in the TPM. CPU XD Support Enables or disables the execute disable mode of the processor. This option is enabled by default. Computrace(R) Enables or disables the optional Computrace® service designed for asset management. You can set this option to: Deactivate (default) Disable Activate SATA -0 Password Displays the current status of the password set for the hard drive connected to the SATA-0 connector on the system board. You can also set a new password. This option is not set by default. NOTE: The system setup program displays a password for each of the hard drives connected to your system board. Power Management AC Recovery Determines how the system responds when AC power is re-applied after a power loss. You can set the AC Recovery to: Power Off (default) Power On Last State Auto On Time Sets time to automatically turn on the computer. Time is kept in the standard 12-hour format (hours:minutes:seconds). Change the startup time by typing the values in the time and AM/PM fields. NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power On is set to disabled. Low Power Mode Enables or disables low power mode. This option is disabled by default. When low power mode is enabled, the integrated network card is disabled when the system is shutdown or in Hibernate mode. Only Add-in NIC cards will be able to remotely wake the system. Remote Wake up Allows the system to power up when a network interface controller receives a wake up signal. You can set Remote Wake up to: Disable (default) Enable Enable with Boot NIC Suspend Mode Sets the power management suspend mode to: S1 S3 (default) NOTE: If the AMT Management Engine (ME) of the system is disabled, the S1 suspend mode is unavailable in the system setup. Fan Control Override Controls the speed of the system fan. NOTE: When enabled, the fan runs at full speed. Maintenance Service Tag Displays the Service Tag of your computer. Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default. SERR Messages Controls the SERR Message mechanism. This option is enabled by default. Some graphics cards require the SERR Message mechanism be disabled. Image Server Lookup Method Specifies how the ImageServer looks for the server address. Static IP DNS NOTE: You must set the Integrated NIC to Enable with ImageServer to set the Lookup Method. ImageServer IP Specifies the primary static IP address of the ImageServer with which the client software communicates. The default IP address is 255.255.255.255 NOTE: You must set the Integrated NIC to Enable with ImageServer to set the ImageServer IP. ImageServer Port Specifies the primary IP port of the image server with which the client software communicates. The default IP port is 06910. Client DHCP Specifies how the client obtains the IP address. Static IP DHCP (default) Client IP Specifies the static IP address of the client. The default IP address is 255.255.255.255 NOTE: To set Client IP you must set Client DHCP to Static IP Client SubnetMask Specifies the subnet mask for the client. The default setting is 255.255.255.255 NOTE: To set Client SubnetMask you must set Client DHCP to Static IP Client Gateway Specifies the gateway IP address for the client. The default setting is 255.255.255.255 NOTE: To set Client SubnetMask you must set Client DHCP to Static IP License Status Displays the current license status. Post Behavior Fast Boot When enabled (default), your computer starts more quickly because it skips certain configurations and tests. NumLock LED Enables or disables the NumLock feature when your computer starts. AC Recovery Determines how the system responds when AC power is re-applied after a power loss. You can set the AC Recovery to: Power Off (default) Power On Last State Auto On Time Sets time to automatically turn on the computer. Time is kept in the standard 12-hour format (hours:minutes:seconds). Change the startup time by typing the values in the time and AM/PM fields. NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power On is set to disabled. Low Power Mode Enables or disables low power mode. This option is disabled by default. When low power mode is enabled, the integrated network card is disabled when the system is shutdown or in Hibernate mode. Only Add-in NIC cards will be able to remotely wake the system. Remote Wake up Allows the system to power up when a network interface con...