Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
RAID Autodetect / AHCI = RAID if signed drives, otherwise AHCI RAID Autodetect / ATA= RAID if signed drives, otherwise ATA RAID On / ATA= SATA is configured for RAID on every boot Legacy = The hard drive controller is configured for legacy mode Legacy mode provides for compatibility with some older operating systems that do not support native resources assigned to the drive controller. RAID Mode is incompatible with ImageServer. Please disable RAID mode if enabling Image Server. S.M.A.R.T. Reporting This field controls whether hard drive errors for integrated drives are reported during system startup. This technology is part of the SMART(Self Monitoring Analysis and Reporting Technology) specification. This option is disabled by default. Drives Enables or disables the SATA or ATA drives connected to the system board. System Configuration Integrated NIC Enables or disables the integrated network card. You can set the integrated NIC to: Disable Enable (default) Enable with PXE Enable with ImageSever ImageServe is incompatible with RAID mode. Please disable RAID if enabling ImageServer. PXE is needed only if intending to boost to an operating system located on a server, not if you are booting on an OS located on a hard drive in this system. USB for Flex bay This field enable and disable the internal USB for Flex Bay, you can set: Disable -Internal USB for Flex Bay is disable Enable -Internal USB for Flex Bay is enable No Boot -Internal USB for Flex Bay is enable, but not bootable. (default) USB Controller Enables or disables the integrated USB controller. You can set the USB controller to: Enable (default) Disable No boot Operating systems with USB support will recognize USB Storage Parallel Port Identifies and defines the parallel port settings. You can set the parallel port to: Disable AT PS/2 (default) EPP ECP No DMA ECP DMA 1 ECP DMA 3 Parallel Port Address Sets the base I/O address of the integrated parallel port. Serial Port #1 Identifies and defines the serial port settings. You can set the serial port to: Disable Auto (default) COM1 COM3 The Operating System may allocate resources even though the setting is disabled. Serial Port #2 Identifies and defines the serial port settings. You can set the serial port to: Disable Auto (default) COM2 COM4 The Operating System may allocate resources even though the setting is disabled. Miscellaneous Devices Enables or disables the following onboard devices: Front USB Rear Dual USB Rear Quad USB PCI slots Audio Boot Sequence Specifies the order in which the computer attempts to find an operating system from the devices specified in this list. Onboard or USB Floppy HDD(will show the model currently in system) Onboard or USB CD-Rom Drive USB Device Drives Diskette drive This field determines how the BIOS configures floppy drives, Operating Systems with USB support will recognize USB Floppy drives regardless of this setting: Disable -All Floppy drive are disable Enable -All floppy drive are enable. The "USB Controller" Setup option will affect floppy operation. SATA Operation configures the operating mode of the integrated hard drive controller. RAID Autodetect / AHCI = RAID if signed drives, otherwise AHCI RAID Autodetect / ATA= RAID if signed drives, otherwise ATA RAID On / ATA= SATA is configured for RAID on every boot Legacy = The hard drive controller is configured for legacy mode Legacy mode provides for compatibility with some older operating systems that do not support native resources assigned to the drive controller. RAID Mode is incompatible with ImageServer. Please disable RAID mode if enabling Image Server. S.M.A.R.T. Reporting This field controls whether hard drive errors for integrated drives are reported during system startup. This technology is part of the SMART(Self Monitoring Analysis and Reporting Technology) specification. This option is disabled by default. Drives Enables or disables the SATA or ATA drives connected to the system board. System Configuration Integrated NIC Enables or disables the integrated network card. You can set the integrated NIC to: Disable Enable (default) Enable with PXE Enable with ImageSever ImageServe is incompatible with RAID mode. Please disable RAID if enabling ImageServer. PXE is needed only if intending to boost to an operating system located on a server, not if you are booting on an OS located on a hard drive in this system. USB for Flex bay This field enable and disable the internal USB for Flex Bay, you can set: Disable -Internal USB for Flex Bay is disable Enable -Internal USB for Flex Bay is enable No Boot -Internal USB for Flex Bay is enable, but not bootable. (default) USB Controller Enables or disables the integrated USB controller. You can set the USB controller to: Enable (default) Disable No boot Operating systems with USB support will recognize USB Storage Parallel Port Identifies and defines the parallel port settings. You can set the parallel port to: Disable AT PS/2 (default) EPP ECP No DMA ECP DMA 1 ...