Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Fujitsu, модель SPARC ENTERPRISE T5220

Производитель: Fujitsu
Размер: 3.94 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


If the system is at the ok prompt, type boot. 3. Use the set /SYS keyswitch_state=normal command to return the virtual keyswitch to Normal mode (default) so that the system can power on and start the boot process. | -> set /SYS keyswitch_state=normal 54 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007 ▼ To Connect to the System Console Output from POST, OpenBoot, and the Solaris OS is displayed in the system console using the network console on the service processor. • Type the start /SP/console command. Multiple users can be connected to the console, but only one can be attached. -> start /SP/console Are you sure you want to start /SP/console (y/n)? y Serial console started. To stop, type #. Note — For more information about POST output, refer to the SPARC Enterprise T5120 and T5220 Servers Service Manual. ▼ To Perform a Normal System Initialization After you issue the start /SYS command, the CPU and memory controllers initialize, and eventually OpenBoot initializes. After a number of system console messages, the ok prompt appears, or the system will boot into the Solaris OS. Note — System behavior depends on how the auto-boot variable is set. See the SPARC Enterprise T5120 and T5220 Servers Service Manual for more information. The following example output is a small section of the complete output. -> start /SYS Find dropin, Copying Done, Size 0000.0000.0000.1110 Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.06e0 cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu cpu vpci mem32base, mem64base, cfgbase: e800000000 e000000000 e900000000 pci /pci@780: Device 0 pci pci /pci@780/pci@0: Device 0 Nothing there /pci@780/pci@0: Device 1 pci pci /pci@7c0/pci@0: Device a Nothing there /pci@7c0/pci@0: Device b Nothing there Chapter 3 Powering On the System 55 /pci@7c0/pci@0: Device c Nothing there /pci@7c0/pci@0: Device d Nothing there /pci@7c0/pci@0: Device e Nothing there /pci@7c0/pci@0: Device f Nothing there Probing I/O buses SPARC Enterprise T522 0, No Keyboard {0} ok To understand the various devices and their path names as represented in the OpenBoot device tree, refer to TABLE 3-1 for disks and TABLE 3-2 for optional PCI cards. TABLE 3-1 Disk Slot Numbers, Logical Device Names, and Physical Device Names Disk Slot Number Logical Device Name* Physical Device Name SlotO c0t0d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@0,0 Slot 1 c0t1d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@1,0 Slot 2 c0t2d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@2,0 Slot 3 c0t3d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@3,0 * The logical device names might appear differently on your system, depending on the number and type of add-on disk controllers installed. TABLE 3-2 Device Identifiers and Devices Device Identifiers Devices /SYS/MB/CMPcpu_number/Pstrand_number CPU Strand (Number: 0-63) /SYS/MB/RISERriser_number/PCIEslot_number PCIe Slot (Number: 0-5) /SYS/MB/RISERriser_number/XAUIcard_number XAUI card (Number: 0-1) /SYS/MB/NETport_number Ethernet ports (Number: 0-3) /SYS/MB/PCIE PCIe root complex /SYS/MB/USBnumber USB ports (Number: 0-1, located on rear of chassis) /SYS/MB/CMP0/L2_BANKnumber (Number: 0-3) /SYS/DVD DVD /SYS/USBBD/USBnumber USB ports (Number: 2-3, located on front of chassis) /SYS/TTYA DB9 Serial Port /SYS/MB/CMP0/BRbranch_number/CHchannel_number/Ddimm_number DIMMS 56 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007 Booting the Solaris Operating System The Solaris OS is preinstalled on the servers on the disk in slot 0. The Solaris OS is not configured (that is, the sys-unconfig command was run in the factory). If you boot the system from this disk, you will be prompted to configure the Solaris OS for your environment. ▼ To Boot the Solaris Operating System 1. At the ok prompt, boot from the disk that contains the Solaris OS. ■ If you know which disk to boot from, skip this step and perform Step 2. ■ If you need to determine which disk to boot from, issue the show-disks command at the ok prompt to see the path to the configured disks, similar to the following: ok show-disks a) /pci@7c0/pci@0/pci@2/pci@0,2/LSILogic,sas@4/disk q) NO SELECTION Enter Selection, q to quit: q ok 2. Type the boot command at the ok prompt. Use the value from Step 1 to construct the boot command. You must append the target to the disk path. In the following example, the server is booted from disk 0 (zero) on a SPARC Enterprise T5120 server. ok boot disk0 Boot device: /pci@7c0/pci@0/pci@8/scsi@2/disk@0,0 File and args: Notice: Unimplemented procedure 'encode-unit' in /pci@7c0/pci@0/pci@2/pci@0/LSILogic,sas@4 Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54. FCode UFS Reader 1.12 00/07/17 15:48:16. Loading: /platform/SUNW,T1000/ufsboot Loading: /platform/sun4v/ufsboot Hostname: hostname The system is coming up. Please wait. NIS domain name is x.x.x.x ...

Эта инструкция также подходит к моделям:
Компьютеры - SPARC ENTERPRISE T5120 (3.94 mb)
Компьютеры - SPARC ENTERPRISE T5120 (3.94 mb)
Компьютеры - SPARC ENTERPRISE T5220 (3.94 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории