Оценок - 2, средний балл: 4 ( )

Производитель: Dell Размер: 3.94 mb Название файла: Язык инструкции:

The procedures are given in the following sections. ■ “To Connect the Service Processor Serial Management Port” on page 35 ■ “To Connect the Service Processor Network Management Port” on page 36 ■ “To Connect the Ethernet Network Cables” on page 36 ■ “To Connect the AC Power Cable to the Server” on page 38 The servers also have serial and USB ports available for connections to optional devices. ■ “TTYA Serial Port” on page 37 ■ “USB Ports” on page 37 Note — When you are finished connecting the cables to the server, ensure that the server can slide smoothly in and out of the rack without binding or damaging the cables. See the section, “To Verify the Operation of the Slide Rails and the CMA” on page 30. Connector Locations FIGURE 2-14 and FIGURE 2-15 show the connectors on the rear and front panels of the SPARC Enterprise T5120 server. 32 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007 FIGURE 2-14 Rear Panel Connectors on the SPARC Enterprise T5120 Server Figure Legend 1 Power Supply 0 8 NET0 2 Power Supply 1 9 NET1 3 Locator LED Button 10 NET2 4 Service Required LED 11 NET3 5 Power OK LED 12 USB Port 0 6 Service Processor Serial Management Port 13 USB Port 1 7 Service Processor Network Management Port 14 TTYA Serial Port USB ports 2 and 3 are located on the front panel (FIGURE 2-15). FIGURE 2-15 Front Panel USB Ports on the SPARC Enterprise T5220 Server — m '•"•"•WV /i" \ *-■ 5 ( 6 Figure Legend 1 Power Button 2 Power OK LED 3 Service Required LED 4 Locator LED Button 5 USB Port 2 6 USB Port 3 FIGURE 2-16 .and FIGURE 2-17 show the connectors on the rear and front panels of the SPARC Enterprise T5220 server. Chapter 2 Installing the SPARC Enterprise T5120 and T5220 Servers 33 FIGURE 2-16 Rear Panel Features on the SPARC Enterprise T5220 Server Figure Legend 1 Power Supply 0 8 NET0 2 Power Supply 1 9 NET1 3 Locator LED Button 10 NET2 4 Service Required LED 11 NET3 5 Power OK LED 12 USB Port 0 6 Service Processor Serial Management Port 13 USB Port 1 7 Service Processor Network Management Port 14 TTYA Serial Port USB ports 2 and 3 are located on the front panel (FIGURE 2-17). FIGURE 2-17 Front Panel USB Ports on the SPARC Enterprise T5220 Server Figure Legend 1 Power Button 2 Power OK LED 3 Service Required LED 34 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007 Figure Legend 4 Locator LED Button 5 USB Port 2 6 USB Port 3 ▼ To Connect the Service Processor Serial Management Port The service processor serial management port is marked SER MGT (FIGURE 2-18). It is the leftmost RJ-45 port on the rear panel. Note — The cable and DB-9 RJ-45 adapters are for the host serial port, and not for the server SER MGT port. FIGURE 2-18 Service Processor Serial Management Port - Rear Panel Use this port for server management. This port is needed to set up the service processor network management port, as detailed in “Enabling the Service Processor Network Management Port” on page 46. Note — Use the service processor serial management port only for server management. It is the default connection between the service processor and a terminal or a computer. Caution — Do not attach a modem to this port. • Connect a Category 5 cable from the SER MGT serial management port to the terminal device. When connecting either a DB-9 or a DB-25 cable, use an adapter to perform the crossovers given for each connector. Chapter 2 Installing the SPARC Enterprise T5120 and T5220 Servers 35 ▼ To Connect the Service Processor Network Management Port The service processor network management port is labeled NET MGT (FIGURE 2-19). It is located just to the right of the serial management (SER MGT) port on the rear panel. FIGURE 2-19 Service Processor Network Management Port - Rear Panel Note — This port is not operational until you configure the network settings (through the serial managment port), as detailed in “To Configure the Service Processor Network Management Port” on page 48. Note — If you have access to a DHCP server on the network, you can see the service processor get an IP address because the DHCP client is enabled by default. Note — The service processor network management port is configured by default to retrieve network settings with Dynamic Host Configuration Protocol (DHCP) and allow connections using Solaris Secure Shell (SSH). You might need to modify these settings for your network. Instructions are given in Chapter 3. • Connect a Category 5 cable from the NET MGT network management port to your network switch or hub. ▼ To Connect the Ethernet Network Cables The server has four network connectors, marked NET0, NET1, NET2, and NET3 (FIGURE 2-20). These connectors are RJ-45 Gigabit Ethernet. 36 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007 FIGURE 2-20 Service Processor Ethernet Network Ports - Rear Panel WAV v.v.v.v.v.v.v ft I# »# piifTj psrri fSFT) 1. Connect a Category 5 ca...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: