Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
A tight coil of tubing in the water line will facilitate moving the brewer to clean the countertop. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow. FIG 6-1 FIG 6-2 Models CTF & CWTF Models CT & CWT 41721 080310 Page 6 PLUMBING REQUIREMENTS-CURRENT TWINS TWINS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1.2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa) . The water inlet fitting is 3.8" flare. 1. Remove six screws securing rear utility cover (if equipped). FIG 7-1 2. Remove cap from the flared fitting on the bottom of the center tube assembly. 3. Flush the water line and securely attach it to the flare fitting on the center tube assembly. FIG 7-2 4. Turn on the water supply. 5. Re-install rear utility cover. FIG 7-3 6. On models with faucet, place an empty vessel beneath the faucet and lift the handle until water is dispensed. FIG 7-1 FIG 7-2 FIG 7-3 41721 111308 Page 7 PLUMBING REQUIREMENTS-EARLY SINGLES As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area. MODEL C: This model is completely portable and requires no attached plumbing. MODELS CT, CTF, CWT, CWTA, CWTB, CWTF, CWTFA & CWTFB, SINGLE CW & SINGLE CWF These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 to 620kPa) from a 1.2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620kPa)to reduce it to 50 psi (345kPa). The water inlet fitting is 1.4" flare. NOTE -Bunn-O-Matic recommends 1.4" copper tubing for installations of less than 25 feet and 3.8" for more than 25 feet from the 1.2" water supply line. A tight coil of tubing in the water line will facilitate moving the brewer to clean the countertop. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow. FIG 8-1 FIG 8-2 Models CTF & CWTF Models CT & CWT 41721 080310 Page 8 PLUMBING REQUIREMENTS-EARLY TWINS TWINS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1.2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa) . The water inlet fitting is 3.8" flare. TWINS 1. Remove six screws securing rear utility cover (if equipped). FIG 9-1 2. Remove cap from the flared fitting on the bottom of the center tube assembly. 3. Flush the water line and securely attach it to the flare fitting on the center tube assembly. FIG 9-2 4. Turn on the water supply. 5. Re-install rear utility cover. FIG 9-3 6. On models with faucet, place an empty vessel beneath the faucet and lift the handle until water is dispensed. P1241FIG 9-1 P1241P1241 FIG 9-3FIG 9-2 41721 111308 Page 9 INITIAL SET-UP CAUTION -The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails. 2. Place an empty dispenser under the funnel. 3. Place the heater switch at the rear of the brewer in the “OFF” lower position and connect the brewer to the power source. 4. Fill the tank with water as directed: 4A. Model C Pour three pitchers of tap water into the screened area on top of the brewer. Allow approximately two minutes between pitchers for water to flow into the tank. While the third pitcher of water is entering the tank, the tank will fill to capacity and the excess will flow from the sprayhead, out of the funnel, and into the dispenser. 4B. Models CT, CTF, CWT, CWTA, CWTB, CWTF, CWTFA, CWTFB, SINGLE CW & SINGLE CWF Connect the brewer to the power source, place the "ON/OFF" switch in the "ON" upper position, and momentarily press and release the start switch. Water will begin flowing into the tank. When water stops flowing into the tank, initiate a second and a third brew cycle. During the third brew cycle the tank will fill to its capacity and the excess will flow from the sprayhead, out of the funnel, and into the dispenser. 5. When the flow of water from the funnel stops, place the heater switch at the rear of the brewer in the “ON” upper...
Эта инструкция также подходит к моделям:Компьютерные аксессуары - CWTF (734.58 kb)