Оценок - 4, средний балл: 4.3 ( )

Производитель: Antec Размер: 105.14 kb Название файла: Язык инструкции:

You may need to turn the switch to the OFF position if your computer crashes and you cannot shut it down with the front panel switch. Hard Disk Installation This case offers two hard disk mounting options. Only use one mounting method at a time. If the case will be moved periodically, then the drives need to be secured to trays as described in the Tray Mount section. If you want the quietest possible installation and the system will not be moved around, then use the suspension system discussed in the Suspension Mount section. Tray Mount There is a hard disk cage right under the external 5.25” drive. You can mount four hard drives using the trays inside it. 1. Open the front bezel as described in Setting Up section. 2. Loosen the two thumbscrews. Swing open the fan cage and gently lift the cage upward to remove it. You will see four drive trays with soft silicon grommets inside the cage. 3. Squeeze the metal clips on each side of the tray and slide the tray out. 4. Mount your hard drive into the drive tray through the bottom silicon grommets with the special screws provided. Note: Don’t over-tighten. Over-tightening the screws will harm the vibration and noise reduction qualities of the silicon grommets. 5. Slide and lock the tray back into the case. 6. Find the appropriate power connector on the PSU and connect it to the device. 7. Repeat this procedure for any additional drives you plan to install. 8. Put the front fan cage back onto the case. If you plan to mount the optional 92mm case fans, you should do it now. See the Cooling section for fan installation. Suspension Mount This is the ultimate hard disk mounting solution to reduce hard drive noise. There are three sets of suspenders inside the cage to mount three hard drives. Each hard drive needs two suspenders (front and rear) to mount. Note: please DO NOT transport your system with your hard disks suspension mounted. The drives may slip from the suspenders causing damage to the hard drives and to other components inside the case. 1. Remove the trays from the cages. Store them in a safe place. You won’t need them. 2. Twist the front suspender. 3. Insert the hard drive through the front suspender from the front. 4. Twist the rear suspender and guide the hard drive through it. 5. Adjust the hard drive position so it has al least 10mm clearance from the front 92mm fan (fan not included). 6. Find the appropriate power connector on the PSU and connect it to the device. 7 7. Repeat the same procedure for the other drives as necessary. 8. Put the front fan cage back to the case. If you plan to mount the optional 92mm case fans, you should do it now. See Cooling system section for fan installation. 5.25” Device Installation There are four external 5.25” drive bays (one with 5.25” to 3.5” adapter). The top two drive bays come with a universal drive door that allows you to hide your optical drive behind the door. 1. Carefully remove the metal plate covering the drive bay. 2. Make sure the clip on the end of the drive rail is angled away from the device and facing forward. Put a plastic drive rail on each side of the 5.25” device. Use the rear set of the screw holes on the drive rails for the top two drive bays and use the front set of screw holes for the lower two drive bays. 3. Slide the device into the drive bay until you hear a click. 4. Mount the other devices accordingly. 5. Connect a large 4-pin connector from the PSU to the male 4-pin connector on each of the devices. External 3.5” Device To install a floppy or other external 3.5” device to the 5.25” to 3.5” adapter: 1. Slide the adapter out. 2. Place the drive to the adapter and fasten the drive with screws provided. 3. Find a 4-pin floppy power connector on the PSU and connect it to the male 4-pin connector on the devices. Cable Organizer There are six hooks (cable organizers) located at the back of the hard drive cage. Loop any long cables you have around the hooks to keep them tucked away. This will prevent tangles and improve airflow through the case. To get to the cable organizer you need to open the right side panel. Cooling System The TriCool™ fan: The case includes one 120mm TriCool™ fan installed in the rear. This fan has a three-speed switch that lets you choose between quiet, performance, or maximum cooling. (See specifications below.) The fan is installed so that the air is blowing out of the case. Connect a large 4-pin connector from the PSU to the male 4-pin connector on the fan. Note: The minimum voltage to start the fan is 5V. We recommend setting the fan speed to High if you choose to connect the fan to a fan control device or to the Fan-Only connector found on some of Antec’s power supplies. A fan-controlled device regulates the fan speed by varying the voltage supplied to it. The voltage may start as low as 4.5 V to 5V. Connecting a TriCool™ set on Medium or Low to a fan-control device may result in the fan not being able to start. The already lowered voltage from the fan control devi...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: