Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this document may be reproduced, modified, distributed, or translated to another language without prior written consent of ADIC. ADIC USA 11431 Willows Road NE Redmond, Washington 98052-4952 Tel.: 1-800-336-1233 Fax: 1-425-881-2296 This document may describe designs for which patents are pending, or have been granted. By publishing this information, ADIC conveys no license under any patent or any other right. ADIC shall not be liable for errors contained herein or for incidental or consequential damages (including lost profits) in connection with the furnishing, performance or use of this material whether based on warranty, contract, or other legal theory. ADIC makes no representation or warranty with respect to the contents of this document and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, ADIC reserves the right to revise or change this document without obligation on the part of ADIC to notify any person or organization of such revision of change. Every effort has been made to acknowledge trademarks and their owners. All trademarks within this document are the property of their respective owners. Trademarked names are used solely for identification or exemplary purposes, and any omissions are unintentional. ADIC is a registered trademark and of Advanced Digital Information Corporation. Published: October 2005 Document Number: 6-01497-01 Rev A Table of Contents Introduction ...................................................................................... 1 Step 1. Unpacking the FastStor 1 .................................................... 2 Step 2. Installing the FastStor 1 in a Rack ....................................... 2 Step 3. Connecting Power Cable ..................................................... 7 Step 4. Removing the Transport Lock.............................................. 8 Step 5. Running Power-On Selftest ................................................. 8 Step 6. Setting the SCSI Address .................................................... 9 Step 7. Connecting the SCSI Bus Cable..........................................9 Step 8. Connecting the Ethernet Connector................................... 11 Step 9. Restarting Your System.....................................................11 Step 10. BCR: Labeling cartridges.................................................11 FastStor 1 Quick Installation Guide Advanced Digital Information Corporation FastStor 1 FastStor 1 Quick Installation Guide Introduction This guide is designed to enable quick installation of the ADIC FastStor 1 autoloader. For additional product and operation details, please refer to the ADIC FastStor 1 Installation and User Manual. The following steps summarize FastStor 1 installation: • Unpack the FastStor 1 • Install the FastStor 1 in a rack • Connect the power cable to the FastStor 1 • Turn on the FastStor 1 • Remove the transport lock by following the instructions displayed on the front panel • Select the appropriate SCSI IDs and unit options • Connect the SCSI interface cable, and optionally the Ethernet cable • Install the backup application software and configure it for use with the FastStor 1 • Load cartridges into the removable magazines In order to complete full installation of the FastStor 1, the following additional materials are required: • Simple hand tools (small Phillips screwdriver) • SCSI Host adapter card with 68-pin wide HD or VHDC connector • Tape application software that is verified with the FastStor 1 • Up to 8 pieces of the appropriate cartridge type to “stock” the FastStor 1 to full capacity. FastStor 1 Quick Installation Guide Advanced Digital Information Corporation FastStor 1 Front Panel of the FastStor 1 Magazine LED Standby LCD Control Magazine front indicators switch display buttons front bezel bezel Figure 1. The FastStor 1's front side Step 1. Unpacking the FastStor 1 Carefully unpack the unit from the shipping container. Save the container and packing materials in case you need to transport the FastStor 1 in the future. The packaging is specifically designed for the loader to ensure it is not damaged during transportation. Review the contents of the shipping container to be sure all parts were included in the shipment. A standard package for the FastStor 1 consists of the following items: • A factory-assembled FastStor 1 unit containing two cartridge magazines. • A Standard Accessory Kit containing: -1 Warranty/Registration Card -Rack-Mount Hardware Kit -2 Line Power Cords: one for USA/Japan and one for European power outlets -1 VHDCI SCSI Interface Cable -1 VHDCI LVD/SE SCSI Terminator -1 Ethernet cable -Tool for Emergency Magazine Release -Media barcode label kit (contains media labels and cleaning cartridge labels) There may be variations of this list. Note: The FastStor 1 is not shipped with tap...