Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Possible causes of Over Temperature condition: • Setpoint is in the boiling range. • Heating element or temperature probe has malfunctioned. • Excessive scale buildup is preventing the element from heating the water. • Heating element relay fails in the “on” state. • No water in the tank. • Hi-limit safety tripped (must be manually reset) To reset the brewer: • Determine the cause of the failure and take appropriate remedial action to rectify the problem. • Press and hold the CANCEL key for three seconds. Four beeps will sound and the brewer will resume normal operation. Quality Timer is normally set for 30 minutes. It can be set for 20 minutes by moving a jumper on the controller. See page 17. After Hours™ is an energy saving feature. The brewer will enter After Hours™ mode if it is not used for three hours. Press the BREW key to immediately return the brewer to normal operation. IMPORTANT: If the original cause of the problem has not been addressed, the brewer will once again go into Over Temperature mode four minutes after being reset. 9 10 BREWING COFFEE CAUTION: Burn Hazard Exposed surfaces of the brewer, brew chamber and decanter may be HOT to the touch, and can cause serious burns. CAUTION: Burn Hazard To avoid splashing or overflowing hot liquids, ALWAYS place an empty decanter under the brew chamber before starting the brew cycle. Failure to comply can cause serious burns. CAUTION: Burn Hazard After a brew cycle, brew chamber contents are HOT. Remove the brew chamber and dispose of used grounds with care. Failure to comply can cause serious burns. NOTE: The brewer will not initiate a second automatic brew cycle until the current cycle plus the drip-out time is completed. If the BREW key is pressed during this time, the BREW light will flash, indicating a brew in progress. NOTE: Water for the hot water faucet is heated in a coil inside of the water tank. Use of the faucet will not affect the volume of water delivered for a brew. However, overuse of the faucet during a brew may lower the temperature of the brew water. A. PREPARATION Place one (1) genuine Bloomfield paper filter in the brew chamber. Add a pre-measured amount of fresh coffee grounds. Gently shake the brew chamber to level the bed of grounds. Slide the brew chamber into place under the brew head. B. AUTOMATIC OPERATION BE sure HEAT light is not lit. Place the appropriate EMPTY decanter in place under the brew chamber. Press the BREW switch. The BREW light will glow and a beep will sound. The solenoid will open for an amount of time determined by the timer setting, admitting a measured quantity of water into the tank. Inlet water will displace a like amount of heated water from the tank. The hot water will be forced into the brew head where it will spray over the bed of grounds. Freshly brewed coffee will begin to fill the container under the brew chamber. At the end of the brew cycle, plus an amount of time set to allow all water to drip out of the brew chamber, three beeps will sound. When the flow and all dripping stops, the coffee is ready to serve. Discard the contents of the brew chamber and rinse it in a sink. When the HEAT light goes out, the brewer is ready for another brew cycle. C. WARMERS At the start of a brew, the MAIN warmer is energized automatically. Press either the FRONT or REAR warmer switch to energize an auxiliary warmer. Set the filled decanter on the selected warmer to keep it warm. Fig. 10 Prepare Brew Chamber Fig. 11 Press BREW to Start 10 BREWING COFFEE CAUTION: Burn Hazard Exposed surfaces of the brewer, brew chamber and decanter may be HOT to the touch, and can cause serious burns. CAUTION: Burn Hazard To avoid splashing or overflowing hot liquids, ALWAYS place an empty decanter under the brew chamber before starting the brew cycle. Failure to comply can cause serious burns. CAUTION: Burn Hazard After a brew cycle, brew chamber contents are HOT. Remove the brew chamber and dispose of used grounds with care. Failure to comply can cause serious burns. NOTE: The brewer will not initiate a second automatic brew cycle until the current cycle plus the drip-out time is completed. If the BREW key is pressed during this time, the BREW light will flash, indicating a brew in progress. NOTE: Water for the hot water faucet is heated in a coil inside of the water tank. Use of the faucet will not affect the volume of water delivered for a brew. However, overuse of the faucet during a brew may lower the temperature of the brew water. A. PREPARATION Place one (1) genuine Bloomfield paper filter in the brew chamber. Add a pre-measured amount of fresh coffee grounds. Gently shake the brew chamber to level the bed of grounds. Slide the brew chamber into place under the brew head. B. AUTOMATIC OPERATION BE sure HEAT light is not lit. Place the appropriate EMPTY decanter in place under the brew chamber. Press the BREW switch. The BREW light will glow and a beep will sound. The solenoid will open for an amount of time determined by...
Эта инструкция также подходит к моделям:Кофеварки - 1012 (1.63 mb)
Кофеварки - 1040 (1.63 mb)