Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
754-0220 Part No. 754-0268 5/8" x 27" Short Belt 5/8" x 51" Long Belt Front (Short) Belt Removal 1. Remove belt cover by removing the four selftapping screws and flat washers. See figure 26. A*-# I WARNING I Muffler may be hot in the area of belt cover. Only remove the belt cover when engine is cool. 14 FIGURE 26. 2. Place gear shift lever in neutral position. Hold friction disc with one hand. Remove three hex bolts and lock washers which hold the friction disc to the variable speed pulley. See figure 27. Lift belt off the variable speed pulley. Upon reassembly of friction disc, tighten the three bolts equally. FIGURE 27. 3. Remove the hex bolt and internal lock washer which holds the belt guard to the engine. See figure 27. Remove the belt guard. Remove and replace the belt. Rear (Long) Belt Removal 1. Follow step numbers 1 and 2 under “Front Belt Removal.” 2. Place the gear shift lever in one of the forward gears (as far forward as possible). 3. Lift up on the idler pulley by hand, and remove the belt from beneath the idler pulley. Lift belt off the transmission pulley and variable speed pulley. See figure 28. FIGURE 28. 4. Reassemble in reverse order with the new belt. NOTE Be certain to assemble the new rear belt in the second groove on the variable speed pulley. TIRE CHAINS It may be necessary to move the right hand wheel assembly to the extreme outside position when using tire chains. See figure 29. NORMAL POSITION FIGURE 29. 15 OFF SEASON STORAGE If the tiller is to be inoperative for a period Ic nger than 30 days, the following precautions are re commended. 1. Working outdoors, drain all fuel from the fuel tank as instructed in the separate er gine manual. A,-# I WARNING X DO NOT DRAIN FUEL WHILE SMOKING, OR IF NEAR AN OPEN FIRE. 2. Drain all the oil from the crankcase (this should be done after the engine has been operated and is still warm) and refil the crankcase with clean new oil. 3. Follow the Instructions found in the engine manual for protecting the inside of the engine for storage. 4. Clean the exterior surfaces of the engino and the entire tiller thoroughly. 5. Wipe tines with oiled rag to prevent rusl. N0TE When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any springs, bearings and cables. TILLER WINTERIZING INSTRUCTIONS FOR USE WITH SNOW BLADE: 1. For cold weather (below 32°F.), drain oil from tiller engine crankcase and replace with grade of oil recommended for cold weather in engine manual. 2. Replace any remaining fuel on hand or in the engine fuel tank with a fresh supply of winter grade fuel. Winter fuels contain additives for faster starts. Keep fuel tank full. m^NOTE It may be necessary to enrich the carburetor idle and high speed jets 1/8 to 1/4 turn (counterclockwise) for good performance. 3. In the spring of the year, before the tilling season, be sure to change engine oil back to SAE 30W detergent oil. 16 TROUBLE SHOOTING CHART SYMPTOM POSSIBLE CAUSE(S) SOLUTION Engine fails to start 1. Check fuel tank for gas. 2. Spark plug lead wire disconnected. 3. Faulty spark plug. 1. Fill tank if empty. 2. Connect lead wire. 3. Spark should jump gap between control electrode and side electrode. If spark does not jump, replace the spark plug. Hard starting or loss of power 1. Spark plug wire loose. 2. Dirty air cleaner. 1. Connect and tighten spark plug wire. 2. Clean air cleaner as described in engine manual. Engine overheats 1. Carburetor not adjusted properly. 2. Air flow restricted. 3. Engine oil level low. 1. Adjust carburetor. See engine manual. 2. Remove blower housing and clean as described in the engine manual. 3. Fill crankcase with the proper oil. Controls do not engage Belts worn and/or stretched. Make control bracket adjustment. See adjustment section of manual. NOTE: For repairs beyond the minor adjustments listed above, please contact your local service dealer. 17 I Models 412 and 418 18 Models 412 and 418 PARTS LIST FOR IV ODE LS 4- 2 AND 418 Tl LLERS REF. *NNO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 710-0136 Hex Bolt 1/4-20 x 1.75" Lg.* 44 710-0623 Hex Wash. Hd. Self-Tap Scr. 2 749-0268 Handle—R.H. 45 712-0241 Hex Nut 3/8-24 Thd.* 3 720-0180 Grip 46 736-0169 L-Wash. 3/8" Scr.* 4 712-0107 Hex Cent. L-Nut 1/4-20 Thd. 47 711-0679 Clevis Pin 5 14844 Clutch Grip 48 15295 Tine Adapter Ass’y. 6 04831 Handle Panel Ass’y. 49 15387 L.H. Tine Ass’y. Comp. 7 749-0269 Handle—L.H. 15386 R.H. Tine Ass’y. Comp. 8 04810 Clutch Handle Ass’y. (Not Shown) 9 714-0149 Hairpin Cotter 50 710-0192 Hex Bolt 3/8-24 x 1.25" Lg.* 10 736-0105 Belleville Wash. .38" I.D. 51 736-0169 L-Wash. 3/8" I.D.* 11 732-0193 Compression Spring .88" 52 712-0241 Hex Nut 3/8-24 Thd.* O.D. x .81" Lg. ...
Эта инструкция также подходит к моделям:Садовые инструменты - 215-418-000 (2.91 mb)