Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Lift up the limit switch and feed the paper past it as shown. Release the limit switch. e. Replace the cover.. f. Refer to routing label on filter paper cover. Feed paper under paper guide shaft and over rounded edge of stainless steel brackets as shown. g. Lift and rotate the idler roller assembly up. h. Route the paper under the brewer cylinder and the idler rollers. i. Release the idler roller assembly, capturing the filter paper. Initial Setup HotCup Operators’ Guide 6740001 22 November, 2007 j. Route the paper into the grounds bucket k. Place the main power switch in the ON position. HotCup Operators’ Guide Initial Setup l. Test the brewer to be sure the paper feeds properly: On the service keypad, press , then press until the display shows BREW TEST. i. Press to test each brewer position: WARNING Keep away from the brewer mechanism while it is operating. Coming into contact with moving parts could injure you. BREW 'R BREW The brewer is in the clamp position. BREW 'R HOMe The brewer is in the open position. ii. Make sure the filter paper feeds properly without jamming. iii. Replace the cup station and grounds bucket. 5. Install the Optional Coin Box Lock a. Install the lock cylinder, washer, and nut in the order shown. b. Tighten the nut. c. Install the lock bar as shown, and secure with the screw. 6. Set Up and Load the Coin Mechanism Standard Coin Mechanism Setting the Quarter Switch. If your coin mechanism is not a MARS TRC 6000, skip this procedure and begin LOADING THE COIN MECHANISM. a. Flip down the front of the coin mechanism as shown, and set the quarter switch. Load the Coin Mechanism. a. Open the cabinet door and the monetary door. b. Insert coins into their respective tubes until each tube has been filled. c. Inspect the tubes for shingled coins and correct if necessary. LOCK BAR SCREW NUT WASHER LOCK CYLINDER 626P0011 November, 2007 23 6740001 Initial Setup HotCup Operators’ Guide MDB Coin Mechanism Install the coin mechanism as follows: WARNING Make sure the main power switch is turned OFF before you work on the merchandiser. Failure to do so could result in death or injury. a. Turn OFF the main power switch. Refer to the instructions provided with the coin mechanism and remove the coin validator assembly. b. Loosen the coin mechanism mounting screws on the merchandiser so they stand off about 1/ 8" (0.3 cm). c. Position the coin mechanism so the three keyed holes fit over the mounting screws. Pull down on the coin mechanism to seat the screws in the keyways. d. Tighten the mounting screws and reinstall the coin validator assembly. 6740001 24 November, 2007 HotCup Operators’ Guide Initial Setup November, 2007 25 6740001 e. The following figure shows a coin mechanism, bill validator, and card reader connected to one another via an MDB. Some monetary configurations may not include all of these devices. Connect your coin mechanism as shown: f. Turn ON the main power switch. Select MDB mech in the SELECT COIN MECHANISM AND OPTIONS procedure on page 2-11. Press until the standby message is displayed, then press . Insert enough coins through the coin slot into the coin tubes to more than cover the empty sensor. Insert coins one at a time and ensure they lay flat in the tubes. The amount of coins you insert is internally recorded. g. Payout about 6 coins to ensure proper loading. h. Finish inserting coins through the coin slot to fill all the tubes with coins. i. Visually check the coin tubes to make sure coins are not shingled. Initial Setup HotCup Operators’ Guide 7. Fill the Tank: a. Make sure the main power switch is ON. b. Turn on the water at its source. c. On the service keypad, press , then press until the display shows TANK.FILL. d. Press . You should hear water running into the tank, and the display will show FILLING. The water will run until either the tank is full or 12 minutes go by, whichever happens first. NOTE The inlet water valve only stays open for 12 minutes at a time. This is a safety feature to prevent water from running into a leaky system and making a mess. It is possible for your tank to take longer than 12 minutes to fill if your location has low water pressure. To be on the safe side, check for leaks if the water runs a long time. If you find none, everything is normal; you just have low water pressure. e. When you hear the water stop running, repeat steps 3 and 4. Under normal circumstances, nothing will happen. If water starts running and the display shows FILLING again, your pressure is low and it is just taking a long time to fill the tank. Repeat this step if necessary to be sure your water tank is full. 8. Fill the Canisters: Open the lid as shown, and carefully pour the appropriate product into the canister. Repeat for all canisters in the machine. 6740001 26 November, 2007 HotCup Operators’ Guide Initial Setup 9. Load Cups: CAUTION Use only cups which have been designed for use in a hot beverage vending machine. a. Support the cup mechanism in the upright posit...
Эта инструкция также подходит к моделям:Кофеварки - 676 (3.29 mb)
Кофеварки - 674 (3.29 mb)
Кофеварки - 676 (3.29 mb)