Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
NOTE: There are fi ller brackets specifically for each side. The way to differentiate this is that on the side of the brackets there are 2 mounting holes. The side where there is a 7/16" gap from the top of the bracket to the mounting hole, must face the top. 3) Attach the right and left cast sides to the top using 2 screws per side. Ensure that the top and sides are aligned. 4) Use a measuring tape to ensure that the distance between the left and right side pieces is 28" (711mm). 5) Connect the ON/OFF switch wires by taking the black and red wires with the blue female ends thru the hole provided and connecting them to the ON/OFF switch. 6) Connect the fan switch wires by taking the black and red wires with the male ends (in the grey harness) thru the hole provided and connect them with the wire connectors from the fan speed control. 7) Insert wires into the strain relief and install into switch box assembly. 8) Place the switch box assembly over the boss on the rear left side piece and secure with one screw. Switch Box Assembly Boss on rear left side piece. 9) Tuck the wires into the faceplate to keep them away from the insert using the clip provided. Attach the clip to the rear of the faceplate to ensure that the wires do not touch the side of the unit. 28" 10) The power cord should be run behind the faceplate panel. U32-5 FPI Direct Vent Gas Insert U32-5 FPI Direct Vent Gas Insert 23 HAMPTON® CAST GRILL INSTALLATION Note: The top grill should be placed with the curved cut-out facing up. 11) Mount the cast faceplate panels onto the insert body, sliding the side fi ller brackets into the space between the glass and the fi rebox. Secure using the 4 remaining black screws, 2 per side. U31 ONLY: Install the glass trim by inserting the side hooks on the glass trim into the 4 slots between the faceplate and the glass. Push the glass trim down fi rmly with both hands to lock into place. Slide side fi ller bracket into gap between glass and fi re box. Side Hook Slots 12) To put on the Hampton® logo, peel the sticker from the back of the logo and place it centered on the bottom left hand corner of the faceplate. Hampton® Logo Left Side Faceplate Before the grills are installed, a grill stop bracket needs to be put in place. 1) The U32 grill stop bracket is installed in the bottom left corner just under the fi rebox as shown below. 2) Place top grill into brackets located inside top of fi rebox as shown. Bracket inside top of fi rebox. 3) The bottom grill, shown in the diagram below, has 2 hinges that are attached to the lip on the bottom of the unit. Secure using 2 screws per hinge. U32 Grill Stop Bracket Bracket Top Grill INSTALLATION INSTALLATION THE KENSINGTON® FRONT INSTALLATION IMPORTANT: Please use the gloves provided when handling the Kensington® Front to avoid fingerprints. 1) Place the Kensington® Front up against the unit , but do not secure. 2) Mount the Kensington® Front onto the firebox by securing in place Make the following wire connections: using 4 screws, 2 per side. Connect the fan switch wires by taking the black and red wires with Screw Screw the male ends (in the grey harness) and connect them with the wire connectors from the fan speed control. Connect the ON/OFF switch wires by taking the black and red wires with the female ends and connect them to the ON/OFF switch. Tuck the wires into the faceplate to keep them away from the insert using the clip provided. Attach the clip to the rear of the faceplate to ensure that the wires do not touch the side of the unit. The power cord should be run behind the faceplate panel. Kensington® Front Left Side Screws Shown 3) Slide the Tabs on the Blanking Plate into the slots located on Front and secure using 2 screws. Blanking Plate Tabs Kensington® Front Blanking Plate U32-5 FPI Direct Vent Gas Insert INSTALLATION THE KENSINGTON® 2-PANEL DOOR INSTALLATION 1) Install the Sub-Frame by hooking the top flange onto the top of the Glass Door and swing the Sub-Frame towards the unit. Pull out the hooks which already secure the Glass Door and place them thru the holes in the bottom of the Sub-Frame to secure both the Glass Door and Sub-Frame in place together. Glass Door Sub-Frame Sub-Frame Hook 2) Mount the 2-panel Door Frame to the flange on Sub-Frame, ensuring to line up holes. Secure using the 6 screws provided. 3) Hook the Left Side Screen Door to the Door Frame by placing the door hinges (top & bottom) over the pins on the Door Frame. Repeat for Right Side Screen Door. Note: It will be easier to put the Screen Door in place by starting with the bottom hinge. Pin on Door Frame Left Side Door Note: If you find that the Left or Right Side Screen Door is lower then the other, use the spacer provided to help align the Doors. The spacer is to be placed over the bottom pin before installing the Screen Door. Spacer U32-5 FPI Direct Vent Gas Insert INSTALLATION THE KENSINGTON® 3-panel Door Installation 1) Install the Sub-Frame by hooking the top flange onto the top...