Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
In addition, when the unit is installed in the middle of a room, the side walls surrounding the unit must not extend beyond the front or rear edge of the unit. See Figure 2. The appliance should be mounted on a fully supported base extending the full width and depth of the unit. The appliance may be located on or near conventional construction materials. However, if installed on combustible materials, such as carpeting, vinyl tile, etc., a metal or wood barrier covering the entire bottom surface must be used. Figure 3 TYPICAL LOCATIONS VERTICAL VENT See-Through (CDST) Corner - Left (CDCL) Corner - Right (CDCR) Peninsula (CDPF) HORIZONTAL VENT - REAR See-Through (CDST) - one side flush with a wall HORIZONTAL VENT - TOP *Note: 3 in. (75 mm) above any horizontal/inclined vent component. Table 2 Model No. Shelf Height inches (mm) Top Vent - with One 90 Degree Elbow Rear Vent - Straight Out the Back Secure Vent Secure Flex Secure Vent Secure Flex CDST CDPF CDCR CDCL 53 1/2 (1359) 55 1/4 (1403) 41 1/8 (1045) 41 1/8 (1045) VENT TERMINATION CLEARANCES These instructions should be used as a guideline and do not supersede local codes in any way. Install vent according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the current standards of CAN/CGAB149.1 and -B149.2 in Canada. Vertical Vent Termination Clearances Terminate single vent caps relative to building components according to Figure 4. Terminate multiple vent terminations according to the installation codes listed above. Horizontal Vent Termination Clearances See Figure 5 on page 5 for horizontal vent termination clearances to any overhead combustible projection less than or equal to 2 ..." (64 mm) and greater than 2..." (64 mm). For additional vent location restrictions refer to Figure 8 on page 6. Shelf Above Fireplace With Rear Venting Do not insulate the space between the appliance and the area above it. Shelf Height (see table) Shelf Above Fireplace With Top Venting Do not insulate the space between the appliance and the area above it. Shelf Height (see table) NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 3" 12" (76 mm) (305 mm) Termination Kit Combustible Projection greater than 2... inches in length Horizontal Vent Termination Clearances Combustible Projection 2... inches or less in length 18" (457 mm) Ventilated Soffit Unventilated Soffit Top Louver Panel Unit Parts Identification Control Compartment Access Panel Figure 5 - Side Elevation View Figure 6 Note - See Figure 39 on page 17 for the exterior wall recess allowances of the square horizontal termination. TYPICAL INSTALLATION SEQUENCE The typical sequence of installation follows, however, each installation is unique resulting in variations to those described. See the page numbers references in the following steps for detailed procedures. Step 1. (page 5) Construct the appliance framing. Position the appliance within the framing and secure with nailing brackets. Step 2. (page 10) Route gas supply line to appliance location. Step 3. (page 10) Install the vent system and exterior termination. Step 4. (page 22) Field Wiring A. Millivolt Appliances – The operating control switch is factory installed. B. Electronic Appliances – Connect 120 Vac electrical power to the appliance receptacle. Step 5. (page 22) Install blower kit (optional equipment). Step 6. (page 23) Make connection to gas supply. Step 7. (page 23) Install the log set, decorative volcanic stone and glowing embers. Step 8. (page 23) Checkout appliance operation. Step 9. (page 24) Install glass enclosure panels. Step 10. (page 24) Adjust burner primary air shutter to achieve proper flame appearance. Step 11. (page 25) Install the hoods. Side Nailing Flanges The fireplace should be secured to the framing at the side(s) and/or rear of the unit using the factory-provided nailing flanges. Install the nailing flanges - 8 (CDST), 4 (CDPF, CDCL and CDCR) - as shown in Figure 7 using the existing screws. Position the fireplace within the framing. When required, the flanges may be bent 90 degrees by hand or with the assistance of a hammer. Use wood screws to secure the nailing flanges to the framing. See Table 2 on page 4 for clearances of framing members to cabinet parts in the nailing flange area. The nailing flange itself is exempt from these clearances. Floor Nailing Tabs Secure the fireplace to the floor as shown in Figure 7. Turn tabs down and secure to the floor with 8d nails or other appropriate fasteners on all sides of the unit which do not have viewing glass panels. CDST SHOWN (CDPF - NO NAILING FLANGES ON END WITH GLASS PANEL) CDCL SHOWN (FOR CDCR VIEW, INTERCHANGE SIDES) Remove these two screws and use them when installing the nailing flanges. Nailing Flanges Figure 7 DETAILED INSTALLATION STEPS 3 - Lift the pressure relief plates and remove the cardboard from underneath each of them. 4 - Open the control compartment access panel by actuating the spring loaded magnetic catches securing ...
Эта инструкция также подходит к моделям:Камины - CDCR-CEN (4.28 mb)
Камины - CDCL-CEP (4.28 mb)
Камины - CDCL-CMN (4.28 mb)
Камины - CDCL-CMP (4.28 mb)