Оценок - 2, средний балл: 4 ( )

Производитель: Regency Размер: 4.94 mb Название файла: Язык инструкции:

Top Flange on Glass Door Bottom Vee-flange Glass Door Glass Door Latch Glass Door Firebox Floor INSTALLING OR REMOVING GLASS DOOR Figure 56 - Note: When installing the glass door, ensure the spacing on both sides are equal. Step 10. BURNER ADJUSTMENTS Flame Appearance and sooting Proper flame appearance is a flame which is blue at the base and becomes yellowish-orange in the body of the flame. When the appliance is first lit, the entire flame may be blue and will gradually turn yellowish- orange during the first 15 minutes of operation. After 15 minutes of operation, if the flame is blue, or if the flame is orange with evidence of sooting (black tip), the air shutter opening may need to be adjusted. If the air shutter openings are closed too far, sooting may develop. Sooting is indicated by black puffs developing at the tips of very long orangeflames. Sootingresultsinblackdeposits forming on the logs, appliance inside surfaces and on exterior surfaces adjacent to the vent termination. Sooting is caused by incomplete combustion in the flames and lack of combustion air entering the air shutter opening. To achieve a warm yellowish-orange flame with an orange body that does not soot, the shutter opening must be adjusted between these two extremes. Air Shutter Adjustment Guidelines • If there is smoke or soot present, first check the log set positioning to ensure that the flames are not impinging on any of the logs. If the log set is properly positioned and a sooting condition still exists, then the air shutter opening should be increased. • Themoreoffsetsintheventsystem,thelarger the air shutter opening will need to be. • An appliance operated with the air shutter opened too far, may have flames that appear blue and transparent. These weak, blue and transparent flames are termed anemic. • Propane models may exhibit flames which candle or appear stringy. If this is present and persists, adjust the air shutter to a more closed position, then operate the appliance for a few more minutes to ensure that the flame normalizes and the flames do not appear sooty. The following chart is provided to aid you in achieving the correct air shutter adjustment for your installation. Air Shutter Adjustment Guidelines: Amount of Flame Air Shutter Primary Air Color Adjustment If air shutter is closed too far Flame will be orange Air shutter gap should be increased If air shutter is open too far Flame will be blue Air shutter gap should be decreased NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Burner Air Shutter Adjustment Procedure Burner Air Shutter Adjustment Procedure WARNINGS • Air shutter adjustment should only be performed by a qualified professional service technician. • Ensure front glass panel are in place and sealed during adjustment. CAUTIONS • Soot will be produced if the air shutter is closed too much. Any damage due to carboning resulting from improperly setting the air shutter is not covered under the warranty. • Theairshutterdoorandnearby appliance surfaces are hot. Exercise caution to avoid injury while adjusting flame appearance. 1. Locate adjustment rod and adjust air shutter to the standard setting as shown in Figure 57 (adjustment rod is located in the lower control area). Note: Rotating the adjustment rod counterclockwise decreases air and clockwise increases air. 2. Light appliance (follow lighting procedure on lighting label in control compartment or see care and operation manual). 3. Allow the burner to operate for at least 15 minutes while observing the flame continuously to ensure that the proper flame appearance has been achieved (see Figure 58). If the following conditions are present, adjust accordingly. • If flame appears weak or sooty, adjust the air shutter,incrementally,to a more open position until the proper flame appearance is achieved. • If flame stays lowered blue, adjust the air shutter, incrementally, to a more closed position until the proper flame appearance is achieved. 4. Leave the control knob (off/pilot/on) in the ON position and the burner OFF/ON switch OFF (and remote switches, if applicable). 5. When satisfied that the burner flame appearance is normal, close the lower control compartment door then proceed to finish the installation. Air Shutter Adjusting Rod Air Shutter Burner Opening Venturi Tube Opening In This Direction Air Shutter Adjusting Decrease Shutter Arms Ref. Air shutter Patent: Opening In This Direction U.S. Pat. 5,553,603 Note - Both air shutters open and close simultaneously when the air shutter adjusting rod is moved. Orifice Increase Shutter Note - Burners are omitted in this view for clarity. Figure 57 -Burner Air Shutter Adjustment Step 11. HOOD INSTALLATION All of these appliances must have hoods installed prior to operating (see Figure 59). Slide the hood into the slots on the lower edge of the cabinet top (see Figure 59). FINISHING REQUIREMENTS Wall Details Complete finished interior wall. To install the appliance facing flush with the finished wall, posi...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: