Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
12) Place rock wool along side the embers on the front of the burner asEnsure not to cover any burner ports. shown. Ensure not to cover any burner ports. 13) Separate platinum embers and place on the burner just in front of the logs. Avoid stacking platinum embers. Completed Log Set Installation 27-28 27-27 27-23 27-24 27-30 27-29 27-26 27-25 Regency® E21-3 Gas Fireplace Insert INSTALLATION 4) Place the trim on the assembled faceplate 8) The power cord should be run behind the FACEPLATE & TRIM panels, aligning the wire connections from faceplate panel. INSTALLATION the switches with the notch on the left side panel. 9) Attach the brass trim to the faceplate by 1) Lay the faceplate panels flat, face down on something soft so they don't scratch. 2) Take the top faceplate and align the holes in it with the holes in the side panels. Using the screws provided, attach from the top of the panel (the holes in the top panel are slightly larger than the holes in the side panel to facilitate easier installation). See diagram 1. Hint: Don't tighten the trim to the bottom of the faceplate side panels with the screws provided. See diagram 1. Diagram 1 Hearth Trim Option: Hearth Trim is an option that can be used tofinish off the installation when the bottom of the fireplace is higher than the hearth or to raise the fireplace. Lay the faceplate side panels flat, face down on something soft so they don't scratch. Attach the Hearth Trim to the bottom of the faceplate side panels with the screws provided. See Diagram 2. Now attach the assembled pieces to the insert body. 3) Using the connectors provided, join the left side trim (with the ON/OFF switch) to the top trim. See diagram 2. Connect the right side trim to the top trim. 5) Connect the fan switch wires by taking the black and red wires with the male ends (in the grey harness) and connect them with the wire connectors from the fan speed control. Diagram 2 6) Connect the ON/OFF switch wires by taking the black and red wires with the female ends and connecting them to the ON/OFF switch. 7) Tuck the wires into the faceplate to keep them away from the insert using the clip provided. Attach the clip to the rear of the faceplate to ensure that the wires do not touch the side of the unit. See diagram 3. Diagram 3 drilling a 1/8" hole through into the faceplate using the hole in the trim as a guide. Fasten the trim to the faceplate panels using the gold plated screws. See diagram 4. Diagram 4 10) Attach the faceplate panels to the insert body using the 4 remaining black screws. See diagram 5. 11) Push the logo plate into the two holes in the bottom left corner of the faceplate. See diagram 4. Diagram 5 Regency® E21-3 Gas Fireplace Insert INSTALLATION FLUSH GLASS FLUSH LOUVERS 1) Install the bottom glass trim onto the glass support. 2) Slide the glass into the bottom glass trim and secure with the glass clips using the 2 phillips head screws at the top. 3) Slide the top glass trim by sliding under the two spring clips. Note: To re-install the glass, reverse the procedure. WARNING The use of substitute glass will void all product warranties. Do not operate the appliance if the glass panel(s) are removed, cracked or broken. Replacement of the glass panel(s) should be done by a qualified service person. 1) The Top Louver is held in place by Spring Clips. Push into place as shown. 2) Install the Spring Hinges on the left and right side of the bottom of the Firebox using 2 screws per hinge. 3) Place the Bottom Louver near the hinge. Flip hinge over the Bottom Louver and secure using 3 screws. Hinge Location Bottom Louver Regency® E21-3 Gas Fireplace Insert 20 Regency® E21-3 Gas Fireplace Insert BAY LOUVERS 1) Install top louver by sliding the two bracket clips into the brackets located on top of the bay door. See below. The fi tted louver leaves a small gap between faceplate bottom and louver top. Diagram 1 NOTE: The top and bottom trim pieces are different. OPTIONAL BAY FRONT IMPORTANT Flush glass must stay in place when bay option is used. The bay front is a decorative overlay only. 1) Place the bay door onto the 2 pins on the top of the unit. 2) Position 2 magnets on the back of each trim piece close to the ends. Place the top and bottom trim pieces on the bay front. 3) Install top and bottom louvers. Note: Top and bottom louvers and brackets are different. See diagram below. 2) Install bottom louver by sliding the two bracket clips into the brackets located underneath the bay door and secure with 2 screws into the bracket on the bottom of the Bay Front as per diagram 1. INSTALLATION INSTALLATION Conversion Kit# 534-969 from NG to LP THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Each Kit contains one LPG Conversion Kit and one DC Sparker Kit. LPG Conversion Kit Contains: Qty. Part # Description 1 904-163 Burner Orifice #54 1 904-529 5/32" Allen Key 1 918-590 Label "Converted to LPG" 1 908-528 Red "LPG" label 1 910-037 LP Injector ...
Эта инструкция также подходит к моделям:Камины - Gas Insert E21-NG3 (3.11 mb)